E&J GF0600059REVB06 ON/OFF switch, Battery gauge, Maximum speed / profile indicator, Horn button

Page 14

Control panel features, VSI integral controller

The VSI control panel is shown at right. A description of each feature follows.

ON/OFF switch

The ON/OFF switch turns wheel- chair power on and off. When wheelchair power is on, the battery gauge illuminates.

max speed /

battery gauge

profile indicator

 

horn button

ON/OFF switch

speed / profile

speed / profile

decrease button

increase button

Battery gauge

control panel

VSI integral controller

The three-color (green, yellow and red) battery gauge illuminates when controller power is on. The battery

gauge shows the charge level of the batteries. As the batteries discharge, the lights go off from green to red, similarly to an automobile’s gas gauge (all lights on = full). When the batteries are nearly discharged, only the red lights will illuminate. When the red lights flash slowly, charge batteries immediately. When you turn the controller on, the battery gauge shows an estimate of the remain- ing battery charge. The battery gauge gives you a more accurate reading about a minute after you start driving the wheelchair. The battery gauge also provides a diagnostics display when wheelchair electrical system problems occur. See TROUBLESHOOTING for a description of the battery gauge diagnostics.

Maximum speed / profile indicator

This is a 5-segment display which indicates the maximum speed setting or which drive profile is selected (if drive profiles have been programmed).

Horn button

This button operates the wheelchair’s horn.

Speed / profile decrease button

This button decreases the maximum speed setting (or selects a lower drive profile, if drive profiles have been programmed).

Speed / profile increase button

This button increases the maximum speed setting (or selects a higher drive profile, if drive profiles have been programmed).

Motors

The motors operate in both the forward and reverse direction. Motor speed and direction are con- trolled by the joystick. The joystick commands are interpreted and applied to the motors by the circuits of the integral controller.

 

 

 

14

GF0600059RevB06, November 2006

Metro Power III Owner’s Manual

Image 14
Contents Metro Power Contents Introduction II Safety Precautions MaintenanceGF0600059RevB06, November GF0600059RevB06, November Electromagnetic interference EMI from radio wave sources Important Information Powered Wheelchair Electromagnetic Interference EMIEMI Warnings III Handling Tips BalanceRamps and Inclines Reaching / bending forward or sidewardReaching / bending backward Ascent DescentIV Getting Started Integral controller Power Drive SystemMotor and battery cables JoystickMaximum speed / profile indicator ON/OFF switchBattery gauge Horn buttonOperating Instructions BatteriesVI Adjustments Arms Flip arm backAttach footrest Adjust footrest lengthFootrest-detachable, swingaway Remove footrest Adjust legrest elevation Attach elevating legrestAdjust elevating legrest footplate extension length Adjust elevating legrest pad position up or downAdjust wheel locks Guidelines to extending battery life VII BatteriesBattery Charger Battery Charger Features Battery Charger Interface Battery charger back panelAC connector AC voltage switchLine connector Battery charger front panelBattery Charger Safety Charging the Batteries Remove and Install Batteries Remove Batteries Install Batteries Metro Power Battery connectionsBattery maintenance Clean batteries Clean battery terminalsViii Maintenance Do-it-yourself MaintenanceCharge batteries Controller Maintenance GeneralList of Tools Control system daily check JoystickCables ConnectorsJoystick boot MountingCheck tires Clean & check upholsteryClean wheelchair Check wheel lock engagementInspect motor brushes Check bearingsTroubleshooting, integral controller IX TroubleshootingTroubleshooting, Power Drive General diagnostic guideBattery gauge diagnostic guide Battery gauge diagnostic guide tableBattery System Gauge Check / Action Lights Troubleshooting, battery charger Front output fuse panelSYMPTOMCHECK-ACTION Transporting the Metro Power ReassemblyXI Limited Warranty Warranty PeriodsGF0600059RevB06, November XII Index GF0600059RevB06, November

GF0600059REVB06 specifications

The E&J GF0600059REVB06 is a cutting-edge technology device that has garnered attention in the market due to its myriad features and robust performance characteristics. This product is designed for versatile applications, offering enhanced efficiency and convenience for users across different sectors.

One of the standout features of the E&J GF0600059REVB06 is its advanced performance capabilities. The device is powered by a high-efficiency processor that not only ensures rapid data processing but also incorporates energy-saving mechanisms. This allows the device to perform complex tasks without consuming excessive power, making it an eco-friendly option for users mindful of their energy consumption.

Equipped with state-of-the-art connectivity options, the E&J GF0600059REVB06 allows seamless integration into existing systems. It supports various communication protocols, which facilitate quick data transfer among devices. Whether connecting to a local network or the cloud, users will appreciate the flexibility this functionality offers for both personal and professional applications.

In terms of design, the E&J GF0600059REVB06 exhibits a sleek and ergonomic appearance that is both aesthetically pleasing and functional. Its compact size makes it suitable for spaces where area is limited, allowing for easy placement without sacrificing performance. Additionally, the device is built from durable materials, ensuring longevity and reliability, even in challenging environments.

The user interface of the E&J GF0600059REVB06 is another highlight. Designed with user-friendliness in mind, it features intuitive navigation that allows users to easily access various functions and settings. This simplicity ensures that even users with limited technical knowledge can operate the device efficiently.

Safety and security are paramount in the design of the E&J GF0600059REVB06. The device incorporates multiple layers of security features, protecting it from unauthorized access and data breaches. These include encryption technologies and user authentication protocols, ensuring that sensitive information remains confidential.

Overall, the E&J GF0600059REVB06 stands out in the market as a reliable, feature-rich device that meets the needs of modern users. Its blend of advanced technology, user-oriented design, and robust security features makes it an excellent choice for anyone seeking an efficient solution for their technological requirements. As such, it has become a preferred option in its category, appealing to a wide range of consumers and professionals alike.