Graco 333282B Setup is Control Modules, Is Control Module Switch Settings

Page 16

Setup the Modules

Setup IS Control Modules

NOTE: Two IS color change control modules may be installed in the hazardous area. The module for colors 1–12 is labeled board 7. The module for colors 13–30 is labeled board 8. An alternate label for Module 8 (Colors 13–30) is provided with the module kit. Affix the label according to your system configuration.

Configure each module according to its designated number, as follows:

NOTICE

To avoid damaging the circuit boards, wear Part No. 112190 grounding strap on your wrist and ground appropriately.

To avoid electrical component damage, remove all system power before plugging any connectors.

1.Remove electrical power from the system.

2.Open the color change module. Locate switches S4, S5, and S6 on the control module board. The switches may be shipped in the OFF position.

3.For each module, set the switches to ON or OFF, as shown in the following table.

IS Control Module Switch Settings

Control

S6

S5

S4

Module

 

 

 

 

 

 

 

 

 

Module 7

 

ON

 

 

ON

 

 

ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF

 

 

OFF

 

 

OFF

 

 

 

 

 

 

 

 

 

 

 

Module 8

 

ON

 

 

ON

 

 

ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF

 

 

OFF

 

 

OFF

 

 

 

 

 

 

 

 

 

 

 

4.Use the following figure and tables to determine the solenoid valve assigned to each valve in the valve manifold.

Figure 2 IS Control Module

16

333282B

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Important Safety Instructions Color Change and Remote Mix Manifold KitsContents Manual No Description Related ManualsManual No Models Non-Intrinsically Safe ModulesControl Module Pressure Valves Intrinsically Safe Modules Kit Identification Label0359 Number of Catalyst + Solvent ValvesModels continue on next 333282B Models Fire and Explosion Hazard Intrinsic Safety Personal Protective Equipment Important Isocyanate ISO Information Isocyanate ConditionsMoisture Sensitivity of Isocyanates Changing MaterialsSetup the Modules Setup Non-IS Control ModulesColor Change Control Modules, Colors, and Catalysts ModuleInlet Manifold Non-IS Control Module Switch SettingsOutlet Manifold Inlet Manifold Outlet Manifold Solenoid Valve Setup is Control Modules Is Control Module Switch SettingsIs Control Module Solenoid Valve Is Control Module Valve SolenoidInstallation Mounting the Control ModulesAir Supply GroundingNon-Hazardous Location Connect the Color Change Control ModulesInstall the Valve Manifolds Install the Valve ManifoldsInstallation Hazardous Location Connect Remote Color Change Control ModuleInstall the Remote Valve Manifolds Install the Remote Mix Manifold Connect the Valve Air LinesNon-Hazardous Area Hazardous AreaInstallation Connect the Fluid Lines Valve Manifold Stack SchematicConnect Non-Circulating Fluid Lines KEY Connect Circulating Fluid Lines Valve Manifold Connections Circulating SystemKEY Install an Expansion Kit Install an Expansion Kit Low Pressure Valve Manifold Shown Cause Solution TroubleshootingColor Change Solenoid Valves Replace the Color Change Board Fuse, Color Change Board Troubleshooting Electrical Schematics Power ModuleEfcm Cable J8 J9 J15 J16 J14 J10 J15 J16 Electrical Schematic, Sheet 3, Hazardous Location Optional Cables and Modules Repair Replace a Color ValveReplace the Color Change Board Fuse Replace a SolenoidFuse Description Replace the Color Change Board Control Module Repair Non-IS Module ShownParts Non-IS Color Change KitsLow Pressure Non-IS Kits Part Description QtyHigh Pressure Non-IS Kits Kit No Kit DescriptionHigh Pressure Non-Circulating Color Change Kits High Pressure Circulating Color Change KitsParts Is Color Change Kits Description QtyLow Pressure is Kits All available kits PartsHigh Pressure is Kits Valve Manifold Kits Low Pressure Valve Manifold KitsNon-Circulating Valve Manifold Kits Kit No Series Circulating Valve Manifold Kits Kit NoValve Manifold Kit Parts Kit No Parts Low Pressure Circulating Valve Manifold Kit Part Quantities High Pressure Valve Manifold Kits Circulating Valve Manifold Kits Kit No SeriesValve Manifold Kit Parts 24T581 Parts High Pressure Circulating Valve Manifold Kit Part Quantities Parts Color Change Control Module Kits Non-IS Color Change Control ModulesConnector 310 321 322 Fitting 305 324 Kit No Position Solenoid Plug Tie Strap Ferrule ConnectorNon-IS Control Module Part Quantities Is Color Change Control Modules 16M00 Is Control Module Part QuantitiesParts Expansion Kits Non-IS Expansion KitsLow Pressure Expansion Kits High Pressure Expansion Kits High Pressure Acid-Compatible Expansion KitsIs Expansion Kits Low Pressure Expansion KitsDimensions Manifold Mounting Bracket, Non-IS 11.44 312 Mm diameter Dimensions Dimensions Technical Data Color Change Kits MetricGraco Standard Warranty Graco Information

333282B specifications

The Graco 333282B is a high-performance airless paint sprayer, designed specifically for both DIY enthusiasts and professional painters who require efficiency and precision. This versatile sprayer is suitable for a variety of projects, including home renovations, commercial applications, and creative crafts.

One of the standout features of the Graco 333282B is its robust TrueLife airless technology, which allows for a smooth and even finish without the hassles associated with traditional paintbrushes or rollers. This technology minimizes overspray while ensuring consistent paint delivery, making it an optimal choice for achieving professional-quality results.

In terms of power, the Graco 333282B incorporates a reliable electric motor that provides enough strength to handle thick materials, such as latex paints and stains. Its powerful motor ensures that users can cover large areas quickly, reducing the time spent on projects. Furthermore, the unit features an adjustable pressure control, allowing users to tailor the flow rate to their specific needs, which enhances versatility across various surfaces and types of paint.

The sprayer's design emphasizes user-friendliness. It is lightweight and portable, making it easy to transport and maneuver around different workspaces. The innovative design also incorporates an easy-to-clean tip, allowing for straightforward maintenance and ensuring longevity in performance. Additionally, the Graco 333282B is equipped with a flexible hose that accommodates movement without compromising pressure, making it easier to reach tight spaces and high walls.

Safety is also a priority, as the Graco 333282B features a built-in tip guard that protects users from accidental injuries when the sprayer is not in use. The unit is intentionally engineered for stability, minimizing the chances of tipping over during operation.

Overall, the Graco 333282B combines advanced technology, user-friendly features, and durability, making it an excellent choice for anyone looking to achieve exceptional painting results efficiently. Whether tackling large-scale projects or smaller DIY tasks, this sprayer delivers the performance necessary to get the job done right.
Top Page Image Contents