Graco 333282B Installation, Mounting the Control Modules, Air Supply, Grounding

Page 18

Installation

Installation

•To avoid electric shock, turn off power at the main circuit breaker before opening the enclosure.

•All electrical wiring must be done by a qualified electrician and comply with all local codes and regulations.

•Do not substitute or modify system components as this may impair intrinsic safety.

•Do not install equipment approved only for non-hazardous location in a hazardous location. See the identification label for the intrinsic safety rating for your model.

This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splashing fluid and moving parts, follow the Pressure Relief Procedure in the PD2K Operation Manual before installing the kit.

Mounting the Control Modules

1.See Dimensions, page 71.

2.Ensure that the wall and mounting hardware are strong enough to support the weight of the equipment, fluid, hoses, and stress cause during operation.

3.Using the equipment as a template, mark the mounting holes on the wall at a convenient height for the operator and so the equipment is easily accessible for maintenance.

NOTE: The smaller color change control modules must be mounted in the Non-IS area. The larger remote color change module may be mounted in the IS area.

4.Drill mounting holes in the wall. Install anchors as needed.

5.Bolt the equipment securely.

Air Supply

Connect a clean and dry air supply to the air inlet fitting (317) of each color change control module in the non-hazardous area and each remote module in the hazardous area. The fitting is for 1/4 in. (6 mm) OD tubing. Use a 5 micron filter. Regulate the air pressure to 85–100 psi (0.6–0.7 MPa, 6.0–7.0 bar).

Grounding

This equipment must be grounded to reduce the risk of static sparking and electric shock. Electric or static sparking can cause fumes to ignite or explode. Improper grounding can cause electric shock. Grounding provides an escape wire for the electric current.

Connect a ground wire from each color change module in the non-hazardous area to a true earth ground.

Intrinsically safe remote color change modules located in the hazardous area must be connected to a true earth ground in the hazardous area.

18

333282B

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Important Safety Instructions Color Change and Remote Mix Manifold KitsContents Related Manuals Manual No DescriptionManual No Models Non-Intrinsically Safe ModulesControl Module Pressure Valves 0359 Intrinsically Safe ModulesKit Identification Label Number of Catalyst + Solvent ValvesModels continue on next 333282B Models Fire and Explosion Hazard Intrinsic Safety Personal Protective Equipment Moisture Sensitivity of Isocyanates Important Isocyanate ISO InformationIsocyanate Conditions Changing MaterialsColor Change Control Modules, Colors, and Catalysts Setup the ModulesSetup Non-IS Control Modules ModuleNon-IS Control Module Switch Settings Inlet ManifoldOutlet Manifold Inlet Manifold Outlet Manifold Solenoid Valve Setup is Control Modules Is Control Module Switch SettingsIs Control Module Solenoid Valve Is Control Module Valve SolenoidAir Supply InstallationMounting the Control Modules GroundingNon-Hazardous Location Connect the Color Change Control ModulesInstall the Valve Manifolds Install the Valve ManifoldsInstallation Hazardous Location Connect Remote Color Change Control ModuleInstall the Remote Valve Manifolds Non-Hazardous Area Install the Remote Mix ManifoldConnect the Valve Air Lines Hazardous AreaInstallation Valve Manifold Stack Schematic Connect the Fluid LinesConnect Non-Circulating Fluid Lines KEY Connect Circulating Fluid Lines Valve Manifold Connections Circulating SystemKEY Install an Expansion Kit Install an Expansion Kit Low Pressure Valve Manifold Shown Troubleshooting Cause SolutionColor Change Solenoid Valves Replace the Color Change Board Fuse, Color Change Board Troubleshooting Electrical Schematics Power ModuleEfcm Cable J8 J9 J15 J16 J14 J10 J15 J16 Electrical Schematic, Sheet 3, Hazardous Location Optional Cables and Modules Repair Replace a Color ValveReplace a Solenoid Replace the Color Change Board FuseFuse Description Replace the Color Change Board Control Module Repair Non-IS Module ShownParts Non-IS Color Change KitsLow Pressure Non-IS Kits Part Description QtyHigh Pressure Non-Circulating Color Change Kits High Pressure Non-IS KitsKit No Kit Description High Pressure Circulating Color Change KitsParts Is Color Change Kits Description QtyLow Pressure is Kits All available kits PartsHigh Pressure is Kits Non-Circulating Valve Manifold Kits Kit No Series Valve Manifold KitsLow Pressure Valve Manifold Kits Circulating Valve Manifold Kits Kit NoValve Manifold Kit Parts Kit No Parts Low Pressure Circulating Valve Manifold Kit Part Quantities High Pressure Valve Manifold Kits Circulating Valve Manifold Kits Kit No SeriesValve Manifold Kit Parts 24T581 Parts High Pressure Circulating Valve Manifold Kit Part Quantities Parts Color Change Control Module Kits Non-IS Color Change Control ModulesKit No Position Solenoid Plug Tie Strap Ferrule Connector Connector 310 321 322 Fitting 305 324Non-IS Control Module Part Quantities Is Color Change Control Modules 16M00 Is Control Module Part QuantitiesParts Low Pressure Expansion Kits High Pressure Expansion Kits Expansion KitsNon-IS Expansion Kits High Pressure Acid-Compatible Expansion KitsIs Expansion Kits Low Pressure Expansion KitsDimensions Manifold Mounting Bracket, Non-IS 11.44 312 Mm diameter Dimensions Dimensions Technical Data Color Change Kits MetricGraco Standard Warranty Graco Information

333282B specifications

The Graco 333282B is a high-performance airless paint sprayer, designed specifically for both DIY enthusiasts and professional painters who require efficiency and precision. This versatile sprayer is suitable for a variety of projects, including home renovations, commercial applications, and creative crafts.

One of the standout features of the Graco 333282B is its robust TrueLife airless technology, which allows for a smooth and even finish without the hassles associated with traditional paintbrushes or rollers. This technology minimizes overspray while ensuring consistent paint delivery, making it an optimal choice for achieving professional-quality results.

In terms of power, the Graco 333282B incorporates a reliable electric motor that provides enough strength to handle thick materials, such as latex paints and stains. Its powerful motor ensures that users can cover large areas quickly, reducing the time spent on projects. Furthermore, the unit features an adjustable pressure control, allowing users to tailor the flow rate to their specific needs, which enhances versatility across various surfaces and types of paint.

The sprayer's design emphasizes user-friendliness. It is lightweight and portable, making it easy to transport and maneuver around different workspaces. The innovative design also incorporates an easy-to-clean tip, allowing for straightforward maintenance and ensuring longevity in performance. Additionally, the Graco 333282B is equipped with a flexible hose that accommodates movement without compromising pressure, making it easier to reach tight spaces and high walls.

Safety is also a priority, as the Graco 333282B features a built-in tip guard that protects users from accidental injuries when the sprayer is not in use. The unit is intentionally engineered for stability, minimizing the chances of tipping over during operation.

Overall, the Graco 333282B combines advanced technology, user-friendly features, and durability, making it an excellent choice for anyone looking to achieve exceptional painting results efficiently. Whether tackling large-scale projects or smaller DIY tasks, this sprayer delivers the performance necessary to get the job done right.
Top Page Image Contents