Toshiba DKT2304-CT manual Direct Wall Mounting, To wall mount the base unit

Page 30

Installation

Step 6: (Optional) Wall Installation

Direct Wall Mounting

If you do not have a standard wall plate, you can mount your telephone directly on a wall. Before mounting your telephone, consider the following:

Select a location away from electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall.

Make sure the wall material is capable of supporting the weight of the base unit.

Use #10 screws with anchoring devices suitable for the wall.

To wall mount the base unit

1.Insert two mounting screws 3-15/16 inches apart. Allow about 3/16 of an inch between the wall and screw heads for mounting the telephone (shown right).

2.Plug and secure the AC adapter cord by following Steps 2 and 3 of the “Standard Wall Plate Mounting” on page 19.

3.Plug one end of the telephone line cord into the LINE jack on the base unit. Optionally, plug one end of a Strata DKT telephone into the PHONE jack. Then place the telephone cord(s) inside the molded channel(s) on the bottom of the wall mount stand.

4.Place the base unit on the posts of the wall screws and push down until it’s firmly seated.

5.Plug the other end of the telephone cord into a telephone wall jack.

6. Plug the AC adapter into a standard 120VAC wall outlet by following Step 7 of the Standard Wall Plate Mounting.

20

Strata CIX and CTX DKT2204-CT/DKT2304-CT Cordless Digital Telephones

Image 30
Contents Digital Solutions Division Publication Information Toshiba America Information SYSTEMS, INC. Tais Toshiba America Information Systems, Inc Contents Handset Operation Troubleshooting Specifications Contents Introduction OrganizationConventions Related Documents and MediaGrand Tour Technology Applications BenefitsHandset DKT2204-CT VOL DKT2304-CT Redial ButtonTalk LCD Display Base UnitCharging Unit Cordless Digital Telephone Standard Parts Grand Tour Installation2 Review Safety InstructionsInstallation Installation Select Location Place DKT3000-series Telephones into 2000-ModeConnect Telephone Cables To connect as a stand-alone telephoneConnect and Apply Power Base UnitCharging Unit Optional Wall Installation Standard Wall Plate MountingDirect Wall Mounting To wall mount the base unitCharging Unit Wall Mounting DKT2204-CTDKT2304-CT Install Handset Battery Pack Raise the Base Unit AntennaInstall Headset Optional Charge Batteries for First TimeAttach Belt Clip Optional To remove the belt clipInstallation Earpiece Volume Handset OperationHandset Controls Mute DKT2204-CT only Handset Ringer Tone and VolumeVibrate Mode Handset Ringer Mute DKT2304-CT onlyF1~F4 Feature Buttons Ringer Off Slide Switch DKT2204-CT onlyMaking a Call Internal CallExternal Call Answer a Call Place a Call on HoldRetrieve Messages Transfer a CallRedial a Number Conference a CallConference Calls Using Strata CTX To conference callsConnecting Two Outside Lines Adding Voice Mail to a ConferenceSwitch a Call to Your Cordless Digital Telephone Switch a Call to the Desk TelephoneSwitch a Call to the Desk Telephone Feature Access Codes Cnf/Trn + #46 + Account code digitsFeature Access Codes Switch a Call to the Desk Telephone #69 + Index Number + old Code + # + new Code + # Call Forward Procedure Feature Button Sequence Call Forward Any Call Set for Another Station Call Forward Incoming Line Call Set for Another Station Feature Access Codes Troubleshooting Specifications TroubleshootingTroubleshooting and Specifications Low Battery Cleaning Charging Unit Contacts Charging Spare Battery Packs DKT2204-CT onlySimultaneous Conversation Channels Range and Performance Radio InterferenceTelephone Line Problems DKT ModePrivacy Specifications Specifications Feature DKT2204-CT DKT2304-CT GeneralIndex DisaIndex ~ W