Toshiba DKT2304-CT manual Select Location, Place DKT3000-series Telephones into 2000-Mode

Page 26

Installation

Step 2: Select Location

Step 2: Select Location

1.Select a location that is not subject to excessive heat or humidity. Keep the base unit and handset away from sources of electrical noise, such as motors and fluorescent lighting.

2.Determine if the base unit will sit on your desk or be wall mounted. If wall mounted, go to Step 6: “(Optional) Wall Installation” on page 19.

3.Place the base unit on a desk or tabletop near a standard 120VAC outlet and within reach of the Strata CTX digital line connection.

Important! Place the base unit to the right of the DKT. If placed on the left, the cordless antenna picks up a tone due to its close proximity to the DKT speaker and electronic parts.

Step 3: Place DKT3000-series Telephones into 2000-Mode

You must place your DKT3000-series telephone into 2000-mode before connecting the cordless telephone; otherwise, the 3000-series telephone will not work.

In 2000-mode, the DKT3000 telephone operation changes are:

Only 16 characters by two lines display on the LCD.

LCD Feature button does not work

Spdial button does not work

To change DKT3000-series telephones into 2000-mode

1. On the DKT3000 telephone, press 3+6+9+Hold (simultaneously).

2. Press #.

3. Press FB7 (or FB10 on the DKT3014). LED On = 2000 mode. LED Off = 3000 mode.

Note Flexible Buttons (FB) are numbered from the bottom up and left to right. FB7 for example would be the seventh button up on the left.

4. Press Hold.

5. Lift the handset to exit programming mode. Wait a few seconds for the telephone to reset itself.

16

Strata CIX and CTX DKT2204-CT/DKT2304-CT Cordless Digital Telephones

Image 26
Contents Digital Solutions Division Publication Information Toshiba America Information SYSTEMS, INC. Tais Toshiba America Information Systems, Inc Contents Handset Operation Troubleshooting Specifications Contents Introduction OrganizationConventions Related Documents and MediaGrand Tour Technology Applications BenefitsHandset DKT2204-CT VOL DKT2304-CT Redial ButtonTalk LCD Display Base UnitCharging Unit Cordless Digital Telephone Standard Parts Grand Tour Installation2 Review Safety InstructionsInstallation Installation Select Location Place DKT3000-series Telephones into 2000-ModeConnect Telephone Cables To connect as a stand-alone telephoneCharging Unit Connect and Apply PowerBase Unit Optional Wall Installation Standard Wall Plate MountingDirect Wall Mounting To wall mount the base unitCharging Unit Wall Mounting DKT2204-CTDKT2304-CT Install Handset Battery Pack Raise the Base Unit AntennaInstall Headset Optional Charge Batteries for First TimeAttach Belt Clip Optional To remove the belt clipInstallation Handset Controls Earpiece VolumeHandset Operation Mute DKT2204-CT only Handset Ringer Tone and VolumeVibrate Mode Handset Ringer Mute DKT2304-CT onlyF1~F4 Feature Buttons Ringer Off Slide Switch DKT2204-CT onlyExternal Call Making a CallInternal Call Answer a Call Place a Call on HoldRetrieve Messages Transfer a CallRedial a Number Conference a CallConference Calls Using Strata CTX To conference callsConnecting Two Outside Lines Adding Voice Mail to a ConferenceSwitch a Call to Your Cordless Digital Telephone Switch a Call to the Desk TelephoneSwitch a Call to the Desk Telephone Feature Access Codes Cnf/Trn + #46 + Account code digitsFeature Access Codes Switch a Call to the Desk Telephone #69 + Index Number + old Code + # + new Code + # Call Forward Procedure Feature Button Sequence Call Forward Any Call Set for Another Station Call Forward Incoming Line Call Set for Another Station Feature Access Codes Troubleshooting Specifications TroubleshootingTroubleshooting and Specifications Low Battery Cleaning Charging Unit Contacts Charging Spare Battery Packs DKT2204-CT onlySimultaneous Conversation Channels Range and Performance Radio InterferencePrivacy Telephone Line ProblemsDKT Mode Specifications Specifications Feature DKT2204-CT DKT2304-CT GeneralIndex DisaIndex ~ W