| Automatic |
| This function is used by ITSP. End user should NOT touch these parameters. |
|
| Upgrade |
| Default is No. Choose “Yes” to enable automatic HTTP upgrade and provisioning. |
|
|
|
|
| |
|
|
| In “Check for upgrade every” field, enter the number of minutes to check the HTTP |
|
|
|
| server for firmware upgrade or configuration changes. When set to “No”, the phone will |
|
|
|
| only perform HTTP upgrade and configuration check once at boot up. |
|
|
|
|
|
|
|
|
|
|
|
| Offhook Auto |
| To configure a User ID/extension to dial automatically when the phone is taken offhook. |
|
| Dial |
|
|
|
|
|
|
|
|
|
|
|
|
|
| DTMF Payload |
| This parameter sets the payload type for DTMF using RFC2833. Default is 101. |
|
| Type |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Onhook |
| Time period when the cradle is pressed (Hook Flash) to simulate FLASH. To prevent |
|
| Threshold |
| unwanted activation of the Flash/Hold and automatic phone |
|
|
|
| value. |
|
|
|
|
|
|
|
|
|
|
|
| Syslog Server |
| The IP address or URL of System log server. This feature is especially useful for ITSPs. |
|
|
|
|
|
|
|
|
|
|
|
| Syslog Level |
| Select the ATA to report the log level. Default is NONE. The level is one of DEBUG, |
|
|
|
| INFO, WARNING or ERROR. Syslog messages are sent based on the following events: |
|
|
|
| • product model/version on boot up (INFO level) |
|
|
|
| • NAT related info (INFO level) |
|
|
|
| • sent or received SIP message (DEBUG level) |
|
|
|
| • SIP message summary (INFO level) |
|
|
|
| • inbound and outbound calls (INFO level) |
|
|
|
| • registration status change (INFO level) |
|
|
|
| • negotiated codec (INFO level) |
|
|
|
| • Ethernet link up (INFO level) |
|
|
|
| • SLIC chip exception (WARNING and ERROR levels) |
|
|
|
| • memory exception (ERROR level) |
|
|
|
| The Syslog uses USER facility. In addition to standard Syslog payload, it contains the |
|
|
|
| following components: GS_LOG: [device MAC address][error code] error message |
|
|
|
| For example: May 19 02:40:38 192.168.1.14 GS_LOG: [00:0b:82:00:a1:be][000]. |
|
|
|
| Ethernet link is up. |
|
|
|
|
|
|
|
|
|
|
|
| NTP server |
| This parameter defines the URI or IP address of the NTP (Network Time Protocol) serve. |
|
|
|
| It is used to display the current date/time. |
|
|
|
|
|
|
|
|
|
|
|
| Distinctive Ring |
| Caller ID must be configured. Select a Distinctive Ring Tone 1 through 3 for a particular |
|
| Tone |
| Caller ID. The BT200 will ONLY use selected ring tones for particular Caller IDs. For all |
|
|
|
| other calls, the BT200 will use System Ring Tone. When selected and no Caller ID is |
|
|
|
| configured, the selected ring tone will be used for all incoming calls. |
|
|
|
|
|
|
|
|
|
|
|
| System Ring |
| System ring tone. Default is North American standard. |
|
| Tone |
| Adjust system ring tone frequencies and cadences based on local telecom standard. |
|
|
|
|
|
|
Grandstream Networks, Inc. | BT200 User Manual | Page 26 of 33 |
| Firmware 1.1.5.15 | Last Updated: 01/2008 |