Oricom pro600 DECT, pro800 DECT Using the Answering Machine Pro800 Only, Rec. and Answer Only

Page 25

Answering Machine (Pro800 Only)

Your answering machine can be ready for use within a few seconds of plugging in the telephone line cord and switching on the mains power.

Just follow the steps in this section to set up and use your answering machine.

Switch on/off

Switches the answering machine on or off. The current answer mode is announced.

Set the answer mode

 

 

 

 

 

 

Switch the answering machine on

 

 

 

 

 

 

 

 

 

 

 

2 sec

 

 

To change the mode between "Answer &

 

 

 

 

 

 

 

 

Rec." and "Answer Only"

Record your outgoing message (OGM)

Your answering machine comes with a default outgoing message but you can record your own personal OGM of up to 2 minutes long.

2 sec

Record your message after the beep

Press to end your recording

Using the Answering Machine (Pro800 Only)

Check your OGM

The current OGM is announced

To return to the factory pre-set OGM, just press the key whilst the current OGM is playing.

Set the answer delay

2 sec (Under base) Enters ring delay mode and announces the current setting.

Select between 2-9 rings or "Time

Saver".

Confirm the number or rings (2-9) or "Time Saver".

Time saver: This feature can save you the cost of a call when you ring in to listen to your messages from another phone. If your answering machine answers after 2 rings you have new messages, if it answers after 5 rings then there are no new messages. Hang up after the 2nd ring and you will not be charged for the call.

23

Pro_600_800.indd 23

2008-11-11 16:17:41

Image 25
Contents Professional Series Table of Contents White pages directory Handset. Slide the battery door firmly into place Installation and ChargerGetting Started Select your countryIf any of these are missing, please contact Oricom directly Purchasing additional handsetsOGM Pro600 Operating the Telephone Operating the TelephoneSec Cordless handsetNavigating in the menu Standby modeSelect New entry Confirm itTelephone TelephoneDeactivate handsfree mode Adjusting the Handsfree volume Boosting the receiver volumeChain dialling Switches the microphone off Mute HS2 Activate registration modeHandset HS1 Conf Activates conference callUsing the menu Using the menuOutgoing calls User profiles cannot be selected in Handsfree modeFor the call Select Ringer volume Handset Ringing volumeVolume Current setting is shown You can also adjust the equaliser settings when youEnter new name and confirm it Level Current setting is shownSelect Keypad Beep ContrastSelect Select base Auto Current setting is shownSelect NZ Caller ID Base Ringing melody Base Ringing volumeShaker Select ShakerDate/Time Open the Menu, select Time Select Date and Time Set Alarm Open the Menu, select Alarm Select Set alarmSelect Set time format ConfirmPhone Book Phone Book Caller ID Caller IDOption Select Delete all Deleting a single calls list entryTake two different calls at the same time Rec. and Answer Only Using the Answering Machine Pro800 OnlyPress to end your recording Check your OGM Current OGM is announcedRecord a memo Set the date and time SecPlay/Pause StopMsgs Listen to your messages/memos via the handsetPress the key to return to standby Memory Full Using Remote Access Pro800 Only Remote Access Pro800 OnlyPIN Code for remote access Changing the PIN codeSwitch to remote access Answer On/Answer mode1st OGM Recording Delete current messageAdvanced Settings Advanced SettingsTroubleshooting TroubleshootingTechnical Properties Technical propertiesDefault settings Default settingsTelephone Answering Machine Warranty Australia Maintenance/GuaranteeCustomer Support REN RN for New Zealand Index IndexIndex Index User Profiles Warranty Australia Australia Customer Support