Oricom ECO710 warranty Getting Started, Getting started

Page 5

Getting Started 3

Getting started

Location

You need to place the base unit within 2 metres of the mains power socket and telephone socket so that the cables will reach. Make sure it is at least 1 metre away from other electrical appliances to avoid interference. Your cordless phone works by sending radio signals between the handset and base. The strength of the signal depends on where you site the base. Putting it as high as possible ensures the best signal.

Handset range

The range is up to 300 metres outdoors when there is a clear line of sight between the base and handset. Any obstruction between the base and handset will reduce the range significantly. With the base indoors and handset either indoors or outdoors, the range will normally be up to 50 metres. Thick stone walls can severely affect the range.

Signal strength

The icon on your handset indicates when you are in range. When out of range of the base the icon flashes and the handset gives an out-of range warning tone every minute. This tone is repeated until you move back into range.

If you move out of range during a call, the telephone call will be disconnected. Move back within range before you make any further calls. The handset will automatically re-connect to the base.

IMPORTANT

!The base station must be plugged into the mains power at all times. Do not plug the telephone line cord into the wall socket until the handset is fully charged. Only use the power and telephone cables supplied with the product.

Battery low warning

If the icon flashes in the display, you will need to recharge the handset before you can use it again.

During charging, theicon in the display will scroll.

Battery performance

In ideal conditions, fully charged batteries should give about 10 hours talk time or 100 hours standby time from a single charge.

Note that new batteries do not reach full capacity until they have been in normal use for several days.

The charge capacity of rechargeable batteries will reduce with time as they wear out, giving the handset less talk/standby time. Eventually they will need to be replaced.

Batteries and handsets may become warm during charging. This is normal.

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Oricom Dect Digital Cordless Telephone Table of Contents Safety Information PBX, damage may result to the PBX Getting started Getting StartedTip If you have a Broadband line Purchasing additional handsetsRadio signals between handset and base unit Setting the time and date on the handsetCharging the batteries InterferenceHandset Phone Function KeysPhone Function Keys Microphone Answering machine operation eco710 only What the icons mean? What the icons mean?Your Telephone Operations Your Telephone OperationsMake and answer calls Change the display languageMute/unmute microphone Adjust the earpiece volumePaging Call waitingSet date/time format Activate/deactivate auto hang-upSet time format Set alarmSet alarm tone Using your phonebook Using your phonebookAccess phonebook Store a contact in the phonebookEdit a phonebook entry Direct access memoryDelete a phonebook entry Delete all entries from the phonebook listDelete direct access memory Add/edit direct access memoryUsing the redial list Using the redial listUsing the call log Using the call logAccess call log Delete a Call Log entryAnswering machine operation By handset ECO710 only Set the answer modeAnswering machine operation by handset eco710 only Turn the answering machine on or offPlayback recorded messages Record a personalized outgoing messagePlayback and delete messages Using the intercom Using the intercomIntercom another handset Transfer an external call to another handsetEstablish a three-party conference call Switch between an internal and external callAdvanced use of your telephone Advanced use of your telephoneChange Master PIN Register your handsetSet prefix Un-register your handsetSet first ring Reset unitChange recall time Answering machine settings eco710 only Answering machine settings ECO710 onlySet ring delay To activate/deactivate remote control accessRemote feature lets you perform the following functions Answering machine settings 30 ECO710 onlyDefault settings Set the OGM voice language optionalTroubleshooting TroubleshootingAlways check first that Everyday useBatteries HandsetTroubleshootingToneIntercom and transfer TroubleshHandsetootiT nge Warranty Warranty Customer Support Customer SupportPage Australia
Related manuals
Manual 40 pages 35.31 Kb
Top Page Image Contents