Oricom BB100 manual Selecting a site for the Base unit, Handset battery charge level

Page 7

Selecting a site for the Base unit

The phone base unit should be installed where the mains adaptor plug will reach the power socket and, the telephone cable will reach your telephone socket and not to close to other electrical equipment (such as washing machines, microwaves, TV, fluorescent lights, etc.

1.Make sure the telephone line is not yet connected to the telephone wall socket.

2.Plug the mains AC adaptor into a mains socket and into the base of the phone. The base will beep, then insert the phone line plug into the phone socket and the other end into the base unit.

Charging the batteries

Please charge the handset batteries for 14 hours before first use to maximise battery performance.

1.Only use the rechargeable batteries supplied with this phone.

2.Remove battery cover on the handset and Install the batteries supplied ensuring you observe the correct polarity. Replace the battery cover.

3.Place the handset on the base unit to charge for at least 14 hours.

4.The red LED CHARGE light on the base unit indicating that the handset is charging, Note: The charge light will stay on even when battery is fully charged – and whenever the handset is on the base.

NOTE: if the charge LED on the base does not light up, reposition the handset in the base unit ensuring the charging points make contact. Regular cleaning is necessary for base and handset charge contacts. Use a clean dry cloth..

Handset battery charge level

1.The Level of the battery power is indicated as a battery icon on the LCD display in the handset. If the battery icon shows empty, your phone needs to be charge.

2.When in use and your phone emit battery low warning tone, your phone needs to be charge.

3.When fully charged your phone will provide up to 8 hours talk time and up to 100 hours of standby time.

Setting the handset date and time

 

1.

Press the OK button to enter MENU settings. You will see

 

in the display.

 

2.

Press DOWN button to scroll to

option

3.

Press OK button to confirm.

 

4.

Press DOWN button to scroll to

.

5.

Press OK button again. The first digit of Date will flash.

6.

Enter two digits of the current date (e.g. 26) from the numeric

 

keypad. Then the digit of Month will flash.

7.

Enter two digits of the current month (e.g. 08) from the numeric

 

keypad. Then the digit of Hour will flash.

 

8.

Enter two digits of the current hour (e.g. 18) from the numeric

 

keypad. Then the digit of Minute will flash. (Note: The Date/Time format is 24 hours.)

9.

Enter two digits of the current minute (e.g. 54) from the keypad.

10.

Press OK button and confirmation tone will be heard..

- 7 -

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Page Contents Using Your PhoneAdvanced Features Safety Information Handset and Base unit Icon Name Description LCD LayoutSetting the handset date and time Handset battery charge levelSelecting a site for the Base unit Preparatory dialling pre-dial Standby modeUsing Your Phone To make and end callsAdjust the handset earpiece volume during a call Using MuteUsing Recall Using Pause functionStoring an entry in the phone book Using the Phone BookFunction Out of range warningDialing a phone book entry Simple way to access phonebookDeleting an entry in the phone book Editing an entry in the phone bookCaller ID CID Deleting a CID record To store a CID entry in the phonebookPersonalising Your Settings Message waiting serviceSelecting Base Ringer melodies Setting the handset ringer volumeSetting Handset Earpiece Volume Setting Base Ringer VolumeAlert tones Renaming the Handset Out of rangeHandset keypad lock/unlock Language selectionAdvanced Features Pause time selection Recall time selectionQuick default settings Reset to factory default settingsProblem Possible Cause Action Taken Troubleshooting GuideCaller ID REN RN for New ZealandWarranty Information
Top Page Image Contents