Radio Shack 2.4 GHz 2-Line Digital Spread Spectrum Cordless Phone with Call Waiting/Caller ID

Page 11

On a Desk Top

1.Insert the bracket’s tabs into the base’s upper tab slots, then press down on the bracket’s clips and insert them into the clip slots.

2.To connect the phone to a two-line phone jack, plug one end of the supplied long two-line modular cord into the TEL LINE 1/2 jack on the back of the phone. Route the cord through the strain-relief slot on the bracket.

Note: If you connect the phone to a two- line phone jack with a two-line cord, do not connect a third line to the TEL LINE 2 jack or the phone will not operate prop- erly. Instead, you can connect another phone device, such as a fax machine or modem.

To connect the phone to two one-line phone jacks, plug one end of the sup- plied long two-line modular cord into TEL LINE 1/2 and plug another cord (not sup- plied) into the TEL LINE 2 jack. Route both cords through the strain-relief slot on the bracket.

To connect the phone to a single one- line phone jack, plug one end of the sup- plied long modular cord into the TEL LINE 1/2 or TEL LINE 2 jack. Route the cord through the strain-relief slot on the bracket.

3.Plug the supplied AC adapter’s barrel plug into the DC IN 9V jack on the back of

the base and route the adapter’s cord through the strain relief slot on the bot- tom of the bracket.

4.Plug the adapter into a standard AC out- let.

5.Connect the phone cord(s) to the modu- lar phone line jack(s).

6.Raise the base’s antenna to a vertical position.

On a Wall Plate or Wall

1.Insert the bracket’s tabs into the base’s lower tab slots, then press down on the bracket’s clips and insert them into the clip slots.

2.Connect the phone line(s) as described in “On a Desk Top”. Use the shorter modular cord to mount the phone on the wall plate.

3.Insert the supplied AC adapter’s barrel plug into the DC IN 9V jack on the back of the base.

4.Route the adapter’s cord through the narrow groove on the bracket. If you are using two phone cords, route the second cord through one of the wide grooves on the bracket.

5.Plug the other end of the short modular cord into the wall plate jack, then align the keyhole slots with the wall plate studs and slide the base downward to

Installation

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents GHz 2-Line Digital Spread Spectrum Cordless Phone Important Information FCC Statement Read this Before InstallationLightning Important Safety InstructionsFCC Wants YOU to Know Important Information Save These Instructions Battery Safety InstructionsContents Caller ID Operation Handset Only TroubleshootingFacedown or Faceup Handset Charging FeaturesImportant Caller ID Information Mounting the Phone InstallationConnecting to the Phone Lines On a Wall Plate or Wall On a Desk TopCONNECTING, CHARGING, and Replacing the Battery Pack Setting the Dialing Mode On the Handset Adjusting the RingerSetting Auto Talk Setting Caller ID/CALL WaitingStoring Your Area Code Basic Operation Using the HandsetUsing Speakerphone Putting a Call on Hold Switching Between the Handset and SpeakerphoneAdjusting Speakerphone Volume Using MuteWay Conferencing Using Both the Handset and SpeakerphoneMaking a Conference Call Using Tone Services on a Pulse Line Using the Phone with Extension PhonesUsing Redial Using FlashUsing a Headset ∗ # & space Memory DialingStoring a Number in Memory HandsetEntering a Pause Editing or Deleting a Number in the Handset’s MemoryBase Dialing a Memory Number CHAIN-DIALING Service NumbersTesting Stored Emergency Numbers Reviewing Memory Numbers Handset onlyFhlWj DWc Caller ID Operation Handset OnlyReviewing Caller ID Records Caller ID MessagesDeleting Caller ID Records ADDING/DELETING the Area CodeDialing Numbers from a Caller ID Record Storing a Caller ID Record to MemoryProblem Suggestion TroubleshootingCare Limited One-Year Warranty
Top Page Image Contents