ClearSounds CL600 manual Phone Mounting Installations, Desk / Table Use, Wall Mount Use

Page 11

PHONE MOUNTING INSTALLATIONS

Choose a location for the CL600 Emergency Connect Telephone that is as central as possible in the house, while providing access to a modular jack and an AC outlet. The telephone may be placed on a shelf or table, or may be ﬁxed to a wall using the mounting bracket.

Plug the AC Adapter into the AC power back on the back of your phone, then into an electrical outlet or surge protector, if you are using one. NOTE: The adapter is required for the telephone to work correctly. If the adapter is accidentally unplugged (or in case of power failure) and if the batteries are dead or not installed, minimal restricted phone features only will work on the phone (make a call or answer incoming call).

IMPORTANT: Please remove the clear plastic Caller ID tab. This ﬁlm tab is only for display and to protect your Caller ID display during shipping.

Desk / Table Use

1.Connect one end of the 6ft telephone cord to the line jack on the back of your CL600 Phone and connect the other end to a modular phone jack (RJ11C).

2.Connect the handset coil cord (curly cord) to the handset and to the telephone (See diagram #7).

3.Lift the handset and listen for a dial tone. If you hear a dial tone, your phone is ready to use. If there is no dial tone, check all your cords to make sure they are plugged in securely.

DIAGRAM #7 – Desk Installation

Wall Mount Use

1.Slide the handset hanger tab out and reverse its position (rotate it 180 degrees). Slide it back into place so that the hook points up (See diagram #8). This will keep the handset from falling out of the cradle when it is mounted on the wall.

2.Plug the 8in short phone cord into the telephone jack on the CL600, run phone cord underneath wall plate adapter and through the opening.

3.Insert the Wall Plate adapter. Hold the wall plate adapter so that the raised mounting pins line up with the phone’s keyholes on the CL600. Once the holes are lined up, push the wall plate adapter in towards the CL600 and then slide the plate upwards until it is securely seated on the phone. (See diagram #9)

4.With the Wall Plate adapter installed, plug the 8in short phone cord into the jack on the wall.

11

Image 11

Contents Page · Register your product · Download additional manuals and troubleshooting tipsPlease Save These Instructions Table of Contents Warranty and Service CL600 Miscellaneous Feature SettingTroubleshooting Guide Maintenance and CareRedial button Features & FunctionsFigure #3 Figure #4 OK button is used to conﬁrm action or a choice on the screen Components Installation StepsInstalling the Optional Batteries Wall Mount Use Phone Mounting InstallationsDesk / Table Use Setting the Dialing Mode Ring Style Strobe & Optional Bed Shaker Ring SignalingRinger Volume Programming the Ringer & Auxiliary AlertProgramming Memory Dial Buttons Diagram #19 Record an emergency connect SOS message Programming emergency connect SOS numberPlay the emergency connect SOS message Using the emergency connect phoneTest the CL600 emergency connect phone To Cancel The CL600 Emergency Connect CallAdvanced CL600 Emergency Connect Phone Operation Remote Audio MonitoringUsing the Remote Audio Monitoring Feature Activate the Remote Audio Monitoring FeatureSetting/Modifying Remote Audio Monitoring Access PIN Code Making and Receiving a Call Using the SpeakerphoneCL600 Phone Operation Auto on HookAudio/Neckloop Jack Using Audio and Telephone Headset Accessory JacksReceiving/Answering a Call Using The Speakerphone Switch between Handset and SpeakerphoneReceiving/Answering a Call Making a CallNeckloop Jack or Headset Jack Voice Ampliﬁcation and Tone Using the Ampliﬁcation FunctionUsing your CL600 emergency connect phone with hearing aids Using the volume reset overrideUsing The Mute Button Using the Outgoing Speech VolumeUsing The Last Number Redial Using The Flash ButtonTotal & New Calls Battery Low IndicatorViewing Your Display Screen Message WaitingReview Call History Viewing Incoming CallsRemove All Call Records Turn OFF the New Calls / Message Waiting Indicator LightRemove Call Record From The Caller ID List Remove a Speciﬁc Call RecordDisplay Screen Messages Turn on The Call Waiting Caller ID FeatureCall Waiting Set The Language CL600 Miscellaneous Feature SettingsSet Area Code / LDS Long Distance Service Code Date format LCD / Screen Contrast AdjustmentChoosing The Date / Hour Format To Add a New Number/Name Setting Up Your Phone BookDIM Hour formatTo Delete a Number From Your Phone Book To Review / Modify a Number/Name In Your Phone BookTo Dial a Number From The Phone Book Recall / Delete One Of the Last 30 Numbers DialedTo Save Numbers From Caller ID To The Phone Book Auto On Hook Troubleshooting GuideThere is a red light that continues to ﬂash Change the Remote Band Battery Maintenance and CareSpeciﬁcations FCC Registration NoticeThis equipment is hearing aid compatible