ClearSounds CL600 manual Using the Ampliﬁcation Function, Voice Ampliﬁcation and Tone

Page 23

Using the Ampliﬁcation Function

The CL600 Phone has an AMPLI button that controls the loudness and tone of the hand- set. Without pressing the AMPLI button, you are able to amplify the handset up to 30 dB of ampliﬁcation. Once the AMPLI button is pressed, an extra level of ampliﬁcation is added providing 30 to 50 dB of gain and tone control.

Voice Ampliﬁcation and Tone

Your CL600 Emergency Connect Telephone is equipped with a specialized ampliﬁcation function designed to ﬁt your needs. You can adjust the volume and tone (sound frequency range) of the incoming voice by simply adjusting Volume and Tone Controls. To use the specialized ampliﬁcation boost and tone control features, follow these directions.

1.Once you have dialed the phone or answered a call, press the AMPLI (amplify) but- ton (See diagram #23). This turns the incoming voice ampliﬁer ON. When the ampliﬁer is ON, you will see the red light on the left side of the AMPLI button light up. i.e.

AMPLI

2.Adjust the volume and tone to ﬁt your needs by adjusting the VOLUME (See diagram #24) and TONE (See diagram #25) controls until you ﬁnd the right levels for you. The Volume Control increase sound volume. Slide the Volume Control to the right to increase the volume and slide it to the left to decrease the volume. The Tone Control allows you to ﬁt your speciﬁc hearing needs. Slide the Tone Control to the left to boost the lower frequency range. Slide the Tone Control to right to boost the high frequency range. This allows individuals with BOTH high frequency and low frequency hearing loss to use the CL600 Phone.

DIAGRAM #23 – Amplify Button

DIAGRAM #24 –Volume Control

DIAGRAM #25 – Tone Control

3.For additional, situational ampliﬁcation, press and hold the HANDSET BOOST but- ton located just below the earpiece on the inside of the handset (See diagram #26). By pressing and holding this additional handset boost button, you get an extra 10 dB gain of ampliﬁcation. IMPORTANT NOTE: The Handset Boost button is designed to be used when listening only. When you are ready to speak, release the button. Press it again when the extra ampliﬁcation is necessary. Failure to release the

23

Image 23

Contents Page · Register your product · Download additional manuals and troubleshooting tipsPlease Save These Instructions Table of Contents Warranty and Service CL600 Miscellaneous Feature SettingTroubleshooting Guide Maintenance and CareRedial button Features & FunctionsFigure #3 Figure #4 OK button is used to conﬁrm action or a choice on the screen Components Installation StepsInstalling the Optional Batteries Wall Mount Use Phone Mounting InstallationsDesk / Table Use Setting the Dialing Mode Ring Style Strobe & Optional Bed Shaker Ring SignalingRinger Volume Programming the Ringer & Auxiliary AlertProgramming Memory Dial Buttons Diagram #19 Record an emergency connect SOS message Programming emergency connect SOS numberPlay the emergency connect SOS message Using the emergency connect phoneTest the CL600 emergency connect phone To Cancel The CL600 Emergency Connect CallAdvanced CL600 Emergency Connect Phone Operation Remote Audio MonitoringUsing the Remote Audio Monitoring Feature Activate the Remote Audio Monitoring FeatureSetting/Modifying Remote Audio Monitoring Access PIN Code Making and Receiving a Call Using the SpeakerphoneCL600 Phone Operation Auto on HookAudio/Neckloop Jack Using Audio and Telephone Headset Accessory JacksReceiving/Answering a Call Using The Speakerphone Switch between Handset and SpeakerphoneReceiving/Answering a Call Making a CallNeckloop Jack or Headset Jack Voice Ampliﬁcation and Tone Using the Ampliﬁcation FunctionUsing your CL600 emergency connect phone with hearing aids Using the volume reset overrideUsing The Mute Button Using the Outgoing Speech VolumeUsing The Last Number Redial Using The Flash ButtonTotal & New Calls Battery Low IndicatorViewing Your Display Screen Message WaitingReview Call History Viewing Incoming CallsRemove All Call Records Turn OFF the New Calls / Message Waiting Indicator LightRemove Call Record From The Caller ID List Remove a Speciﬁc Call RecordDisplay Screen Messages Turn on The Call Waiting Caller ID FeatureCall Waiting Set The Language CL600 Miscellaneous Feature SettingsSet Area Code / LDS Long Distance Service Code Date format LCD / Screen Contrast AdjustmentChoosing The Date / Hour Format To Add a New Number/Name Setting Up Your Phone BookDIM Hour formatTo Delete a Number From Your Phone Book To Review / Modify a Number/Name In Your Phone BookTo Dial a Number From The Phone Book Recall / Delete One Of the Last 30 Numbers DialedTo Save Numbers From Caller ID To The Phone Book Auto On Hook Troubleshooting GuideThere is a red light that continues to ﬂash Change the Remote Band Battery Maintenance and CareSpeciﬁcations FCC Registration NoticeThis equipment is hearing aid compatible