ClearSounds CL600 manual This equipment is hearing aid compatible

Page 39

represented by 10 are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.]

e)If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your rights to file a complaint with the FCC if you believe it is necessary.

f)The telephone company may make changes in its facilities, equipment, operation or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.

g)Should you experience trouble with the equipment, please contact: ClearSounds

Communications Attn: Repair Center, 8160 S Madison St, Burr Ridge, IL 60527,

800-965-9043 V/TTY, 888-654-9219 FAX, e-mail: repairs@clearsounds.com for repair or warranty information. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.

h)Please follow instructions for repairing if any (e.g. battery replacement section); otherwise do not alter or repair any part of device except as specified.

i)Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation for information.

j)NOTICE: If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of the CL600 does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.

k)This equipment is hearing aid compatible.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These Limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip- ment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio com- munications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television recep- tion, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio TV technician for help.

39

Image 39
Contents Page · Register your product · Download additional manuals and troubleshooting tipsPlease Save These Instructions Table of Contents Warranty and Service CL600 Miscellaneous Feature SettingTroubleshooting Guide Maintenance and CareRedial button Features & FunctionsFigure #3 Figure #4 OK button is used to confirm action or a choice on the screen Installation Steps Installing the Optional BatteriesComponents Phone Mounting Installations Desk / Table UseWall Mount Use Setting the Dialing Mode Ring Style Strobe & Optional Bed Shaker Ring SignalingRinger Volume Programming the Ringer & Auxiliary AlertProgramming Memory Dial Buttons Diagram #19 Record an emergency connect SOS message Programming emergency connect SOS numberPlay the emergency connect SOS message Using the emergency connect phoneTest the CL600 emergency connect phone To Cancel The CL600 Emergency Connect CallAdvanced CL600 Emergency Connect Phone Operation Remote Audio MonitoringActivate the Remote Audio Monitoring Feature Setting/Modifying Remote Audio Monitoring Access PIN CodeUsing the Remote Audio Monitoring Feature Making and Receiving a Call Using the SpeakerphoneCL600 Phone Operation Auto on HookAudio/Neckloop Jack Using Audio and Telephone Headset Accessory JacksReceiving/Answering a Call Using The Speakerphone Switch between Handset and SpeakerphoneMaking a Call Neckloop Jack or Headset JackReceiving/Answering a Call Voice Amplification and Tone Using the Amplification FunctionUsing your CL600 emergency connect phone with hearing aids Using the volume reset overrideUsing The Mute Button Using the Outgoing Speech VolumeUsing The Last Number Redial Using The Flash ButtonTotal & New Calls Battery Low IndicatorViewing Your Display Screen Message WaitingReview Call History Viewing Incoming CallsRemove All Call Records Turn OFF the New Calls / Message Waiting Indicator LightRemove Call Record From The Caller ID List Remove a Specific Call RecordTurn on The Call Waiting Caller ID Feature Call WaitingDisplay Screen Messages CL600 Miscellaneous Feature Settings Set Area Code / LDS Long Distance Service CodeSet The Language LCD / Screen Contrast Adjustment Choosing The Date / Hour FormatDate format To Add a New Number/Name Setting Up Your Phone BookDIM Hour formatTo Delete a Number From Your Phone Book To Review / Modify a Number/Name In Your Phone BookRecall / Delete One Of the Last 30 Numbers Dialed To Save Numbers From Caller ID To The Phone BookTo Dial a Number From The Phone Book Auto On Hook Troubleshooting GuideThere is a red light that continues to flash Change the Remote Band Battery Maintenance and CareSpecifications FCC Registration NoticeThis equipment is hearing aid compatible