Agilent Technologies 5071A manual Available Accessories and Options

Page 50

Specifications

Available Accessories and Options

Available Accessories and Options

This section describes the additions, changes, and deletions to the information that appears in the Available Accessories and Options section of the Specification chapter for either the HP 5071A Operating and Programming manual or the HP 5071A Assembly-Level Service manual.

Option 048: The description for the HP 5089A has additional information:

The HP 5089A will not power the HP 5071A when option 048 is present.

Options

Any TCO Option: The descriptions for the telecommunications output options are added beneath the description of option 048:

104:1.544 Mbbs, 100 Ω balanced, Super Frame (D4)

105:1.544 Mbbs, 100 Ω balanced, Extended Super Frame (ESF)

220:2.048 Mbbs, 120 Ω balanced, Common Channel Signaling

221:2.048 Mbbs, 120 Ω balanced, Channel Associated Signaling

222:2.048 Mbbs, 120 Ω balanced, Channel Associated Signaling with CRC4

270:2.048 Mbbs, 75 Ω unbalanced, Common Channel Signaling

271:2.048 Mbbs, 75 Ω unbalanced, Channel Associated Signaling

272:2.048 Mbbs, 75 Ω unbalanced, Channel Associated Signaling with CRC4

The above telecommunications options comply with CCITT recommendations G.703 and G.704 for electrical signal characteristics and formatted content.

In addition to the G.703 & G.704 defined outputs, all telecommunications options provide the following input/outputs:

•8 kHz Frame Sync In

•8 kHz Frame Sync Out

•Sync Out (Telecommunications Rate 1.544 or 2.048 Mbbs)

3-4

Image 50

Contents 7HOHFRPPXQLFDWLRQV2SWLRQV Page Telecommunications Options Supplemental Manual Before Cleaning Manual Updating Changes 05071-90042, December Contents Service Supplemental Characteristics Available Accessories and OptionsContents How to Use This Manual Instrument IdentificationManual Organization How to Order ManualsInstruments Covered by This manual Operating and Programming Introducing the 5071A 5071A Major FeaturesIntroduction Operating The 5071A5071A at a Glance ConnectorsGetting Started Rear-Panel Connections5071A Rear Panel Connections Fuse Performing Basic Tasks Powering Down the 5071AStarting The 5071A Synchronizing to an External 1 PPS ReferenceMonitoring Status Using the 5071ADisabling the Internal -Standby Battery Case of Difficulty Front-Panel Indicators and MessagesRear-Panel Output Connectors Restarting the 5071AScpi Subsystem Commands 5071A Command References5071A Command Summary Scpi CommandsSpecifications Operating the 5071A From External Dc Power InstallationPower Requirements Preparation for UseLong-Term Storage Internal Standby Battery MaintenanceReplacing the External Dc Input Power Fuse Preparing the RP 5071-A For External-Dc OperationAssembly-Level Service 5071A Operational Verification Rear-Panel Output Signal ChecksPerformance Tests Option ServiceAssembly Identification and Location First Power On Top-Level Diagnostic Tree OrganizationTop-Level Diagnostic Tree Diagnostic Section Warm-up and Fatal Error Diagnostic Tree Power-Supply Diagnostic Tree Advisory Messages SubsectionNo Operation From Internal Standby Battery Ac-Line Fuse Fault Isolation r/o LF1/T14.0.0 Ext. Dc Input Fuse Fault Internal-Battery Charger Test4 A8 Front/Rear-Panel Sync Input Test Assembly/Module Diagnostic Trees Diagnostic SectionA8 Diagnostic Tree A/M Subsection 3 1 PPS Outputs Test 5 A8-to-Chassis Interconnect Test4.1 A9-to-Chassis TCO Option signal Interconnect Test A9 Diagnostic Tree A/M Subsection 5.0 A9 Mon Signal Test6.0 A9 J4 80-MHz Signal Test Simplified Functional Description Theory of OperationIntroduction A1 Motherboard Circuit DescriptionInput/Output Block Power Supply BlockFunctional Block Descriptions Operating Firmware Warning Mode Instrument Control BlockReference Oscillator/RF-Chain Block Interconnections Power Supply Block External Dc Input Circuit A1 Motherboard Circuit DescriptionOvervoltage Protection Circuit A11 Power Steering Logic Assembly A1 Power Supply/Distribution Schematic Diagram48V Subpanel Assembly Input Chassis GroundB1 Internal-Standby Battery A1 Power-Supply Block DiagramReplaceable Parts Exchange AssembliesReplaceable Parts Backdating Backdating Specifications Time Standard Supplemental CharacteristicsInternal Standby Battery Nominal Values EnvironmentalWeight Accessories Furnished Dc input connectorAvailable Accessories and Options OptionsService and Support From front matter Declaration of Conformity Page Page Manual Part Number