Motorola ME4066 Series Connecting the Base Station and Mains Adaptor, Connecting the Charger Unit

Page 6

Installation

Do not expose the base station and charger unit to direct sunlight. Do not allow the base station and charger unit to become wet. They should not be set up in rooms which are subject to condensation or corrosive steam or a high concentration of dust (e.g. cellars, garages or conservatories). The room temperature must be between 00C and 350C.

Connecting the Base Station and Mains Adaptor

1.

Plug the telephone line cord into the base station socket.

Installation

2.

Route the cord underneath the base station towards the back.

3.

Plug the other end into the telephone wall socket.

 

4.

Connect the mains power supply.

 

 

The base station does not have a power

 

 

switch. Only use the mains adaptor supplied

 

 

with your phone.

 

Connecting the Charger Unit

Insert the plug of the mains adaptor in the socket on the underneath of the charger unit. Plug the mains adaptor into the mains socket. The charger unit is now ready to use.

9

Inserting the Batteries

Open the battery compartment by pushing downwards on the

battery compartment cover. Insert the 2 x AAA batteries supplied, observing the correct polarity.

The mobile handset will not operate if the batteries are inserted incorrectly. There is also a possibility that the handset may be damaged.

Replace the cover on the battery compartment and push it upwards until it clicks into place. Place the handset on the base station.

You will hear a beep and the charging light comes on.

Note: When used for the first time, allow the batteries to charge for at least 14 hours without interruption. If possible, only take the handset out of the base station when

the charging process has ended. This will help to guarantee optimum operation.

Note: To ensure the battery charges properly, clean the charging contacts on the handset and charger with a soft, dry cloth once a month. Clean more often if the unit is subject to grease, dust or high humidity.

Attaching the Belt Clip

10

Push the belt clip into the opening on the back of the handset.

The clip will bend slightly until it clicks into place.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Image 6
Contents Users Guide Digital Cordless TelephoneWelcome Contents Important Safety Instructions Important Safety InstructionsImportant InstructionsSafety Installation GuidelinesSetting up the Base Station and Charger Unit Important InstructionsSafety InstallationPackage Contents Technical AmendmentsInserting the Batteries Connecting the Base Station and Mains AdaptorConnecting the Charger Unit Attaching the Belt ClipTechnical Data FeaturesFeatures Attaching the HeadsetControl Buttons Control ButtonsDisplay Icons Menu Structure Using the Telephone Dialing from the Phone Book Taking CallsPrefix Dialing Call Log OperationsTeleconference and Intercom Call Transfering Muting the MicrophoneHolding Calls / Forwarding Calls Entering a Dialing Pause PStore Entries Phone BookPhone Book View EntriesDelete Entries Phone Book Handset SettingsChanging the Ringer Volume Changing the Ringer Melody external/internalSwitching the Key Tone On/Off Saving a PrefixActivating/Deactivating Automatic Call Answering Activating/Deactivating Call Timer Default SettingsRegistering Additional Handsets Entering/Changing Emergency Number Base Station SettingsBarring Calls Changing the Flash TimeSelect Dial Mode Changing the PINDelete HS Answering Machine Operation Switch Answering Machine ON/OFF preset to onClock Setting GeneralMailboxes How to Record Your AnnouncementSet remote access code Recording Announcement A1 Announce Only set to OFFVoice Prompt language selection MachineAnswering Recording a MemoDeleting Messages Important informationMessage Playback Using the phone Quick ReferenceHandset Settings Base Settings Answering MachineQuick Reference Warranty Remote OperationPage What is not Covered by the Warranty OUT of Warranty Repairs