Sony SPP-Q110, SPP-Q120 operating instructions Making and receiving calls, Speed dialing

Prepare the battery pack

Insert the battery into the handset and charge first before you start using your phone.

1	1Slide open the battery compartment lid of
	the handset.
	2Connect the battery connector with correct
	porality (black and red cords).
	3Insert the battery pack, and close the lid.
2	4Place the handset on the base unit.
	The CHARGE lamp lights up when the
	handset is properly seated on the charge
	Black terminals of the base unit. Charge the
Red	battery pack for more than 12 hours so that
	the battery is fully charged. The CHARGE
	lamp remains lit even after charging is

Additional tasks

To	Do this
Switch to another call*	Press (FLASH).
("call waiting" service)	Press the button again to get back to the first caller.

* You need to subscribe to this service from your telephone company.

Notes

•Do not cover the microphone during the conversation; otherwise, the other party cannot hear your voice.

•If you hear beeps during the conversation, move closer to the base unit; otherwise, the call will be disconnected after 15 seconds. Note that, however, you may not hear beeps if it’s noisy on the handset.

If interference occurs on the handset

When you press (TALK), the handset automatically searches for the channel with the best reception. However, if you notice interference during a conversation, move closer to the base unit.

If interference persists, press (CHANNEL) to switch to another channel to improve the sound quality of your telephone conversation.

3

completed.

Note

If you hear five short beeps when you press (CHANNEL), move closer to the base unit.

Battery duration

A fully charged battery pack lasts for about:

• 12 hours when you use the handset continuously

• 14 days when the handset is standing by.

If the handset battery becomes weak during a call

The handset will beep every three seconds with the TALK/BATT LOW lamp flashing at the same time. Finish your call and charge the battery pack.

Caution

If this occurs, you cannot use the handset without charging it for more than 1 minutes.

4

CHARGE lamp

Notes

•The battery pack will gradually discharge over a long period of time, even if not in use.

•The battery works best when charged every two or three days. For best performance, do not return the handset to the base unit after every call.

If the battery runs out completely, the speed dial numbers and the digital security code will be erased. If this happens, charge it on the base unit for over 12 hours. Then reprogram the speed dial numbers, and assign a new digital security code (see “Resetting the digital security code”). You may need to charge the battery several times before it is recharged to its full capacity.

Redialing

1 Press (TALK), and wait until the TALK/BATT LOW lamp lights up. 2 Press (REDIAL/PAUSE) to redial the number last dialed.

Note

If the number exceeds 32 digits, the beeps will alert you that the number can’t be dialed.

To erase the last phone number dialed

Press (REDIAL/PAUSE) twice.

When to purchase a new battery pack

If the battery lasts only a few minutes even after 12 hours of charging, the usable life of the battery has expired and needs replacement. Contact your local Sony authorized dealer or service center, and ask for Sony BP-T16 rechargeable battery pack.

Making and receiving calls

The number will be erased from the memory, and you’ll hear a long confirmation beep.

Speed dialing

You can dial with a touch of a few keys by storing a phone number on a dialing key.

Storing phone numbers

Making calls

1 Pick up the handset from the base unit.

2 Press (TALK), and wait until the TALK/BATT LOW lamp lights up.

1 Press (PGM).

The TALK/BATT LOW lamp flashes.

2 Press (SPEEDÊDIAL).

The dialing keys light up (SPP-Q120

TALK/BATT LOW lamp

(FLASH)

The dialing keys light up (SPP-Q120 only).

You then hear a dial tone. If you hear beeps, move closer to the base unit.

only).

3 Press one of the dialing keys ((0) to

(9)) to store a phone number on. You hear a confirmation beep.

TONE(*)

(REDIAL/PAUSE)

(CHANNEL)

Microphone

Additional tasks

3

4

Dial the phone number.

When you're done talking, press (OFF).

The TALK/BATT LOW lamp goes off.

TALK/BATT LOW Lamp

4 Enter the phone number you want to store.

You can enter up to 16 digits, including a tone and a pause, each of which is counted as one digit.

5 Press (PGM).

(REDIAL/PAUSE)

You hear a long confirmation beep, and the number is stored. The TALK/

To	Do this
Switch to tone dialing	Press TONE (*) after you’re connected.
temporarily	The line will remain in tone dialing until disconnected.

Receiving calls

1 When you hear the phone ring;

•Press (TALK) (or any key except (OFF)). or

•Pick up the handset from the base unit when the handset is placed on the base unit.

The TALK/BATT LOW lamp lights up.

2 When you’re done talking, replace the handset on the base unit or press (OFF).

The TALK/BATT LOW lamp goes off.

BATT LOW lamp goes off.

Note

Do not allow more than 20 seconds to elapse between each step of the procedure.

Tips

• If you enter a wrong number, press (PGM), then start from the beginning.

• You can attach the supplied directory on the handset.

• You can’t receive calls while you’re storing numbers.

To store a number to be dialed via Private Branch Exchange (PBX)

Before entering a phone number in Step 4, do as follows:

1 Enter the outside line access digit (e.g., 9). 2 Press (REDIAL/PAUSE).

SPP Q110/Q120 3 856 344 11 E U