Sony CD145 Make a call Predialling, Call is initiated, Direct dialling, Call from the call Log

Page 18

press , , enter 4-digit PIN code (default PIN is 0000) and press in idle mode to its default settings.The handset will go back to country code selection screen and you can select the country code again. If country selection is not needed, the handset will go back to idle screen after reset.

3.5Register your handset You will need to register your new handset or if you wish to register the handset to a different base unit.You can register up to four handsets on a single base station.

Before entering the 4-digit PIN,

press on the base unit for around three seconds when the base is in standby mode.

1Press ,

2Enter the default or existing 4-digit PIN code. (Default PIN is 0000)

3 Press to start registration

Note

If the PIN code you entered is incorrect, a long beep is emitted and the phone returns to standby mode.

16

4Using your phone

4.1Make a call

4.1.1Predialling

1Enter the phone number (maximum 24 digits)

2Press to dial the number

•The call is initiated.

4.1.2Direct dialling

1Press to take the line

2Enter the phone number

•The call is initiated.

4.1.3Call from the call

log

This feature is available if you have subscribed the Caller Line Identification service (CLI) with your network provider.

1Press to show the latest call log entry

2Press repeatedly to scroll through the list of unanswered calls to select

your desired unanswered call

3 Press to dial the

selected number

Getting started

Image 18

Contents CD145 EN Digital Cordless TelephonePage Table of contents How to change the remote PIN Default settings Frequently asked questionsAnswering machine Power requirements Easily accessibleNational recovery & recycling system Use one of the following disposal optionsDisposal instructions for batteries Using GAP standard compliance Electric, Magnetic and Electromagnetic Fields EMFPage Line cord What’s in the boxTelephone handset Base station BatteriesTalk key Overview Phone Handset ACall Log keyPhonebook key Redial/Flash keyCall Transfer / Intercom / Conference Alphanumeric keypad GStar keyHHash key Program keyDisplay icons on the handset Event LED Forward key Delete key Base stationBackward key + / keyGetting started Connect the base StationInstall rechargeable Batteries Slide out the battery cover Place the batteries asConfigure your Phone Country setting table PressAppear on the screen Tip Direct dialling Make a call PrediallingCall is initiated Call from the call LogDisplay shows the last number dialled Call from the phonebookCall from the redial list End a callHow to use Intercom How to make a second call During a callHow to answer a Second call RecallCalled handset rings if it is available How to make an Internal callPress on the called handset Conference call is initiatedHow to find a handset During the conference callExternal call is put on hold automatically Is shown on the display How to adjust earpiece volume During a callCall in progress Mute/Unmute microphone During a call Number is saved Selected memory locationHow to delete the entire phonebook How to access the phonebook Idle modeHow to edit the phonebook entry or Delete a number All the phonebook entries are deletedHow to access the redial list How to access the call logHow to delete the entire call log Settings How to set the time 1 PressHow to activate/deactivate Keypad lock How to set the ring VolumeHow to set How to select recall TimeHow to turn on/turn off the key Tone How to select dial ModeCurrent settings are displayed How to set the auto prefixHow to access your voice mail number How to change the master PINHow to program voice mailbox number New PIN is savedHow to restore to default settings Your phone is reset to its default settingsHow to turn off How to set answer delayHow to record your outgoing message How to select the default outgoing Message How to play Outgoing messageHow to delete outgoing message Country setting table on SectionHow to play Incoming messagesHow to screen an incoming call How to remotely access yourPress and hold for two Seconds to delete all old messages How to change the remote PIN New remote access PIN Is savedKeys Description Default settings Items Default valuesCommunication is lost during a call Connection Handset does not switch onPhone does not work at all Poor audio qualityCall Waiting call cannot be answered AppearsSet-up Caller ID does not work properly Handset displays nothing, but only the is blinkingPhonebook entry cannot be stored Caller does not hear meNoise interference on your radio or television Handset is unable to registerUnable to perform remote operation