Southwestern Bell owner manual Telephone Installation Setting Up Your FM2572

Telephone Installation (Cont.)

Setting Up Your FM2572

When you plug in your unit for the first time, it will take approximately 14 seconds for the unit to check its memory (It will announce "Wait For Operation"). When the memory check is complete, your system will announce "Unit Ready" and will reset to answer incoming calls. It will answer incoming calls with a prerecorded greeting; "Hello,We are not available now; please leave your name and number after the beep." To record a personalized greeting refer to page 15.

4.Connect the desk mount bracket to the bottom of the base. This will tilt the base for enhanced Caller ID visibility.

Wall Mounting On a Wall Plate

1. Connect the coil cord into the handset

On Two Screws

1.Fasten two screws into the wall, placing them 3-1/4" apart vertically. They should extend 3/16" from the wall.

2.Connect the coil cord into the handset jack and the jack on the bottom of the unit.

3.Connect the AC adaptor into the AC ADAPTOR JACK on the bottom of the unit and plug the other end into the 110/120 volt outlet.

4.Simply connect the long telephone line cord to the modular jack and thread through the groove on the bottom of the unit. (Fig.G)

To Set Language

1. If "SET LANGUAGE" is not displayed on	flash
the screen, press and hold CALL BACK
Button for 2 seconds. The LCD display
will show:

		3. Press the "ERASE" Button again to
		end the setting. The display will show
2.	Rotate the "REVIEW" knob to select	the default time and day. The unit is
3.	English, French or Spanish.	now ready to receive calls.	Month Day
	Press the"ERASE" Button to confirm		AM
	the language selected. The unit will

then proceed to the contrast setting mode.

The correct date and time are automatically set when your FM2572 receives its first call.

jack and the jack on the bottom of the unit.

2. Connect the AC adaptor into the AC

ADAPTOR JACK on the bottom of the

unit and plug the other end into the

110/120 volt outlet.

3. Connect the short telephone line cord

to the modular jack located on the bottom of the base. Insert the other end into the wall jack, making sure it snaps firmly in place (Fig.F).

Figure G

5.Mount the unit by fitting the two screws into the keyway holes on the bottom of the base. Pull down gently for a snug fit. The LINE CORD should hang down behind the unit.

6.Plug the LINE CORD into the wall modular jack.

To Set LCD Display Contrast

1.Rotate the "REVIEW" knob clockwise to make the contrast lighter or counter clockwise to make the contrast darker.

2.Press "ERASE" Button to confirm selection.The unit will then proceed

to the area code setting mode. flash

To Set Area Code

Note: In order for the Caller ID Redial feature to work properly, you must set your area code.

1. Rotate the "REVIEW" knob

clockwise or counter clockwise

until you have entered the correct

Note:

1. If you try to use the telephone before

finishing the Caller ID set up, or if

you pause more than 40 seconds during

any of the above steps, the display will

show "SET LANGUAGE" to remind

you to finish this sequence.

2. To set up your FM2572 again, press and

hold the "CALL BACK" Button for 2

seconds to restart setup.

3. If you only want to adjust the LCD

display contrast in standby mode or in

review mode, press and hold the

"CALL BACK" and "ERASE" Button at

the same time. LCD will show

"CONTRAST s t", to indicate that

your FM2572 has entered contrast

Figure F

4.Position the bottom of the base over the two studs of the wall plate. Pull down to lock in place (Fig.F).

10

first digit of your local area code.

Press the "ERASE" Button to move

to the next digit.

2. Repeat step 1 for the programming of

the second and third digits of your

local area code.

setting mode.

11