VTech VT9127 important safety instructions FCC, Acta and IC Regulations, VTech Communications Inc

Page 25

FCC, ACTA AND IC REGULATIONS

This equipment complies with Parts 15 of the Federal Communications Commission (FCC) rules for the United States. It also complies with regulations RSS210 and CS-03 of Industry and Science Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

A label is located on the underside of the Base Unit containing either the FCC registration number and Ringer Equivalence Number (REN) or the IC registration number and Load Number. You must, upon request, provide this information to your local telephone company.

This equipment is compatible with inductively coupled hearing aids.

Should you experience trouble with this telephone equipment, please contact:

VTech Communications Inc

CUSTOMER SERVICE, at 1-800-595-9511. In Canada, call VTECH Telecommunications at 1-800-267-7377.

For repair/warranty information, the telephone company may ask you to disconnect this equipment from the line network until the problem has been corrected.

FCC Part 15

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

The equipment has been tested and found to comply with part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet or on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

FCC Part 68 and ACTA

If this equipment was approved for connection to the telephone network prior to July 23, 2001, it complies with Part 68 of the Federal Communications Commission (FCC) rules. If the equipment was approved after that date, it complies with the Part 68 rules and with Technical Requirements for Connection of Equipment to the Telephone Network adopted by the Administrative Council for Terminal Attachments (ACTA). We are required to provide you with the following information.

1.Product identifier and REN information

The label on the back or bottom of this equipment contains, among other things, an identifier indicating product approval and the Ringer Equivalence Number (REN). This information must be provided to your local telephone company upon request. For equipment approved prior to July 23, 2001, the product identifier is preceded by the phrase “FCC Reg No.” and the REN is listed separately. For equipment approved after that date, the product identifier is preceded by “US” and a colon (:), and the REN is encoded in the product identifier without a decimal point as the sixth and seventh characters following the colon. For example, the product identifier US:AAAEQ03T123XYZ would indicate an REN of 0.3.

The REN is used to determine how many devices you may connect to your telephone line and still have them ring when you are called. In most, but not all areas, the sum of all RENs

25

ADDITIONAL INFORMATION

Image 25
Contents Table of Contents Important Safety Instructions Parts Check List Handset Layout Base Layout Follow these Instructions Installation of Battery Pack in HandsetSetting UP Your VT9127 TONE/PULSE Selection Ringer SelectionPress PROG/CHAN Handset Display Handset is in idle modeBasic Operation Volume ControlMaking Calls Channel ChangingAnswering Calls Using RedialFlash Hold Receiving and Storing Calls Caller ID/CALL Waiting IDAbout Caller ID Review Caller IDDial a Displayed Number Deleting Records from Call HistoryStore a Caller ID Record in Phone Book Memory Err Display Screen MessagesStore Memory Numbers Phone BookDelete Numbers Stored in Memory Edit Numbers Stored in MemoryDial Memory Numbers Until Messages Waiting is Message WaitingOperation Belt Clip InstallationDo not pull up from the bottom of the clip Cleaning Your Telephone MaintenanceAvoid Rough Treatment Avoid WaterPhone DOESN’T Work AT ALL Case of DifficultyNo Dial Tone Vtech Communications atYOU Hear Other Calls While Using Your Phone Handset does not Ring When YOU Receive a CallYour Caller Fades in and OUT Common Cure for Electronic EquipmentWhat does this limited warranty cover? Limited WarrantyLimitations How do you get warranty service?VTech Communications Inc FCC, Acta and IC RegulationsConnection and use with the nationwide telephone network Rbrctm Seal Technical Specifications Page Issued