Nortel Networks RTU-292 operation manual 10Password Protection, 11Voice Prompts Enable

Page 26

RTU-292 Operations Manual

2.8.12 PASSWORD PROTECTION

Dipswitch SW1-5 enables or disables the RTU-292's password protection feature. Password protection prevents unauthorized access to the system from the PSTN line when the RTU-292 is in the Automated Operation Mode. (See section 3.7 for a full explanation of Automated Mode Operation and the use of the Password Protection Feature). The factory setting is disabled, SW1-5 Off. To enable the password protection feature, turn SW1-5 On. The factory default password is “1 2 3 4”, but may be changed to any number up to 10 digits long. See Table 3-2.

Table 2-10Password Protection

SW1-5

Passwords

Off

Disabled *

 

 

On

Enabled

 

 

2.8.13 VOICE PROMPTS

Dipswitch SW1-6 enables or disables the use of Voice Prompts in the RTU-292. This feature should be enabled only if the Voice Prompt Option is installed. See section 3.7 for an explanation of the Voice Prompt feature operation, and section 7.2 for field installation. The factory default setting: disabled if the Voice Prompt Option is not installed and enabled if it is.

Table 2-11Voice Prompts Enable

SW1-6

Voice Prompts

Off

Disabled

On

Enabled

 

 

2.8.14 LOCAL PHONE / LOCAL PHONE RING-THROUGH

Dipswitch SW1-7 enables or disables the RTU-292 Local Phone Option. This feature should be enabled only if the Local Phone Option is installed. The factory setting is: Disabled (SW1-7 Off) if the Local Phone Option is not installed and enabled (SW1-7 On) if it is. See section 3.7 for an explanation of Local Phone Option operation, and section 7.3 for field installation instructions.

SW1-8 enables the Local Phone Ring-Through feature. This causes the local phone to ring whenever a call is received by the RTU-292 via the PSTN input. When disabled, the local phone may still be used to send and receive calls, but will not ring when a call is received. Set SW1-8 to On to enable Local Phone Ring-Through, and Off to disable this feature. This switch should always be set to Off (disabled) when the Local Phone Option is not installed. The factory setting is On (enabled) when the Local Phone Option is installed and Off (disabled) otherwise.

JPS Communications, Inc.

2-10

Image 26
Contents JPS Communications, Inc JPS P/N Revision JulyProprietary Statement Phone 919 Fax 919Table of Contents RTU-292 Theory of Operation Front Panel Buttons and Indicators Schematic Diagrams List Of Figures List of Tables Glossary This page intentionally left blank Scope Description GeneralTelephone Interface AssembliesMain Board Radio Interface Power Supply SectionHandset/Speaker Interface DSP ModuleEquipment and Accessories Supplied Qty Part NumberOptions Optional Equipment Not SuppliedRTU-292 Specifications Reshipment of Equipment GeneralUnpacking and Inspection FCC Part 68 Regulations Installation OverviewInstallation Considerations 1RTU-292 Factory Default Settings Feature / Function Adjustment Default SettingDC Input Power Selection Power RequirementsInput Power Selection Line Voltage SelectionSetting Telephone Send and Receive Levels Configuring the RTU-292Programming Mode Setup Parameters Type of System Recommended Phone Line SettingsFactory default settings are indicated by an asterisk Telephone Send/Receive LevelsVOX Sensitivity VOX HangtimeVOX Hangtime VOX SensitivityTelephone Ring Volume Dial ModeDial Mode RX Line Input ImpedanceFull/Half Duplex Radio Control ModeSW1-3 Radio Control Off Disabled Enabled SW2-8 Full/Half Duplex Off Full Duplex11Voice Prompts Enable Password Protection10Password Protection Voice PromptsInterconnect Information 12Local Phone Enable14TX Level Set-up Mode 13 Local Phone RingthroughPin Function Telephone Connection15J1 TEL Line RJ-11C Radio Connection17J7 Handset RJ12C Jack Handset Connector16P1-RADIO DB-9 Male Terminal Block 18Terminal Block 6 PositionSetting the Transmit Level Audio Level Setup and Adjustments19P2 RS-232 Connector DB-9 Male 5 RS-232 ConnectionSetting the Receive Level 10.1.2RTU-292 Operations Manual Outline Dimensions Control and Connector Locations Location Of Internal Option Settings Internal Option Setting Details Audio Interface Wiring Diagram Interface Details Installation Checklist Installation ChecklistOptions Installation and Configuration Front Panel CONTROLS, Indicators and Connectors Keypad Speaker Volume ControlPhones Volume Control TEL Line ButtonsAudible Ring Button Speaker ButtonsAuto ANS Button KEY Pushbutton4 J2 Local Phone Connector Rear Panel Connectors1 P1 Radio Connector 7 P1 AC Power ConnectorUSE of the RTU-292 Speaker to Monitor Audio OperationOperation Overview Placing a Telephone CallReceiving a Telephone Call Using the Handset with the RadioConnecting the Radio to the Telephone Line Putting a Telephone Call on Hold8.2 Manual Phone Patch Procedure8.1 8.5 8.38.4 8.6Self Test Negative Acknowledge ErrorRemote KEY Automated OperationRadio Is Keyed Keyed Disconnecting DisconnectWaiting For Input Query Radio Is Unkeyed UnkeyedRTU-292 Adapts To The Phone Line Caller Enters The Password if enabledCaller Dials The RTU-292 Terminating a Call RTU-292 Enters the Command ModePlacing a Call in the Command Mode Dtmf Control Commands Operating the RTU-292 from the Front Panel Keypad1Standard Dtmf Operational Commands Dtmf Command Function2Programming Mode Dtmf Commands Calling Timer RTU-292 Password ProtectionInactivity Disconnect Timer Programming the Speed Dial Directory Using the RTU-292 Speed Dial FeatureUsing the Speed Dial Feature Optional 4 Wire Operation Factory ResetSpeed Dial Reset Audio BUS Arrangement Front Panel Buttons and IndicatorsMain Board Telephone Receive Circuits Telephone Interface CircuitsTelephone Send Circuits Receiver Input Amplifier Ring Detector and Tone RingerRadio Interface Circuits Transmitter Audio OutputMicrophone Circuit Dtmf DetectorFSK Modem Speaker and Headphone CircuitsNoise Generator Audio DelayAdaptive Hybrid Peak DetectorDC Power Supply Power SupplyAC Power Supply 8 CPUPrompt Tone Generator Option Interface BoardVoice Prompt Option Speech ProcessorInterface Circuitry Local Phone OptionVoice Prompt Software DIAL/BUSY GeneratorsRS-232 Remote Control Overview Commands Sent to the RTU-2921Command Summary Audible Ring Command Null CommandAuto Answer Command Date Command Dial CommandDisconnect Command Dtmf CommandHandset Phone Command Handset Radio CommandSpeaker Phone Command Speaker Radio CommandSpeed Dial Command SD nnALL num.? CRTel-Line Phone Command Tel-Line Radio CommandTime Command Software Version CommandStatus Returned from the RTU-292 Response SummaryCall Starting Response Null ResponseAuto Answer Response Dtmf Response Dial ResponseDisconnect Response Handset Radio Response Elapsed Time ResponseHandset Phone Response Speaker Phone Response Speaker Radio ResponseTel-Line Radio Response Speed Dial ResponseTel-Line Phone Response Time/Date Response Version ResponseCall Progress Responses from the RTU-292 Response Error CodesResponse Error Codes Call Progress ResponsesPerformance Testing Preventive MaintenanceRepair or Replacement AlignmentHybrid Balance Measurement Hybrid Balance Test Set-Up Main Hybrid Test Procedure Alternate Hybrid Test Procedure VOX Sensitivity Test Set-Up VOX Test Procedure VOX Sensitivity MeasurementFault Analysis Replaceable Parts List DescriptionDescription Reference Designator RTU-292 Operations Manual Reference Designator Special Software Versions RTU-292 OptionsSW1-6 Voice Prompts Off Disabled Enabled Installation and ConfigurationVoice Prompts Enable OperationVoice Prompt Option Installation SW1-7 Local Phone Off Disabled Enabled Local Phone Option Installation and ConfigurationLocal Phone Enable SW1-8 Ringthrough Off Disabled Enabled5Local Phone Dtmf Commands Local Phone Option OperationVMM-100 Analog Interface VMM-100 HardwareVMM-100 DSP Section VMR Algorithm VMM-100 Installation and ConfigurationVMM-100 Software Noise Reduction AlgorithmVMM-100 Option Installation VMM-100 Specifications EnvironmentalVMM-100 I/O Connector Information P9 VMM-100 Switch FunctionsDtmf Access Option After the Call Begins Squelch Break Access Option RTU-292 Prompts for ConfirmationCall Logging Option Setting The TimeSetting The Date Checking The Time And DateRadio Control Option Controlling the Radio VIA the RTU-292 Front Panel Keypad9DTMF Radio Control Commands Command Followed By Command DescriptionSchematic Diagrams Blank Index Environmental Self Test Speech Processor