Nortel Networks 150 manual Network Access

Page 107

Chapter 10 Dialing Translation 107

An example of a Dialing Translation Table from a site in Mountainview, California

INPUT

OUTPUT

 

 

 

 

Network Access

Explanation

The Dialing Translation Table is empty. The local network in Mountainview supports 10 digit national dialing with recognized long distance charging.

In situations like the Mountainview example, there is no need to build a Dialing Translation Table.

The Dialing Table Translation results in a number that can be dialed on the local network. The final step is to prefix any digits required to reach the local network from your Norstar system. For systems that are behind a PBX or PABX, typically in North America ·must be prefixed to the telephone number. For systems attached to Central Office (CO) lines no digits need to be prefixed.

Dialing Translation properties

Dialing Translation is controlled by four properties:

Long distance access code

This prefix, if specified, is removed from any numbers entered by the subscriber if it is not needed to make the call. This simplifies the creation of the Dialing Translation Table. For North America, set the long distance access code to 1. The default for this parameter is none. The field for this parameter is a maximum of 1 digit.

Area code

If the phone number entered appears to be missing an area code, an area code is prefixed to the number. The area code is considered missing if the number has fewer than 10 digits. The default for this parameter is none. The field for this parameter is a maximum of 6 digits. If this parameter is set to none, no area code is prefixed to the telephone number.

Access code

In North America, the access code is usually 9. This number is prefixed to all numbers after Translation to access the local telephone network. If your system is attached directly to CO lines, set the Access Code to none. The default for this parameter is none. The field for this parameter is a maximum of 2 digits.

Reply translation

If set to N (no), the caller must manually trim the Caller ID message information for the number to be dialed on the local network. If the reply translation is set to Y (yes), then the Reply feature uses the Dialing Translation Table to dial the call. The default for this parameter is N.

To make it easier for subscribers, set the Reply Translation to Y if a Dialing Translation Table is created. If a Dialing Translation Table is not created, set the Reply Translation to N.

CallPilot 150 Telephone Administration Guide

Page 106 Page 108
Image 107
Page 106 Page 108
Contents CallPilot Telephone Administration Guide CallPilot 150 Telephone Administration Guide Contents Chapter Working with mailboxes Chapter Working with CCR Trees Chapter Troubleshooting CallPilot About CallPilot CallPilot featuresChapter Getting started with CallPilot Desktop Messaging CallPilot optionsMessage Networking Call CenterTelephone How to get helpGetting started with CallPilot P0919416 Who can use CallPilot Chapter Using CallPilotSystem timeout Using CallPilot with a two line display telephoneTo enter a character Using the dialpadAbout telephone buttons Symbols and conventions used in this guideUsing CallPilot P0919416 Chapter CallPilot mailboxes About installing mailboxesSystem Administrator Mailbox Subscriber mailboxes General Delivery MailboxGuest mailboxes When to use Guest mailboxesInformation mailboxes Class of Service features Prompt language Mailbox Class of ServiceClass of Service Class of Service valuesCompany Directory Mailbox propertiesAlternate extensions To restrict outdialing Restricting outdialingTo initialize a mailbox Initializing a mailboxTo add a Subscriber mailbox Chapter Working with mailboxesAdding a Subscriber mailbox Press OK To add a Guest mailbox Adding a Guest mailboxTo add an Information mailbox Adding an Information mailboxTo add multiple mailboxes Adding many mailboxesPress OK to end the session Incorrect password lock-out About mailbox passwordsTo change a mailbox Changing a mailboxService classx Press Next Press to end the session To delete a mailbox Deleting a mailboxAbout Group List Numbers About Group ListsAbout Sending Group List messages To add a Group List Adding a Group ListTo change a Group List Changing a Group ListADD DEL View To delete a Group List Deleting a Group ListAbout the Automated Attendant Chapter Setting up the Automated AttendantGreeting Tables Greeting Type Default start timesAbout Company Greetings To record a company Greeting Recording a GreetingCustom prompts Setting up a Greeting TableTo set up a Greeting Table Chng DAY Next Mo nonb 600 pm To configure how a line is answered Configuring line answeringTo change or view how a line is answered Changing line configurationTo assign or change the number of rings Assigning the number of rings before CallPilot answersTo set up Touchtone Gate Setting up Touchtone GateTT gatecustom Destination number Table entry Incoming call example About the Clid Routing TableTo route a phone number To change or delete a phone number in the Clid Routing Table About Custom Call Routing Chapter Custom Call RoutingHome node Planning and designing a CCR TreeComponents of a CCR Tree Sub-menus Information MessagesPaths Mailbox nodesTransfer nodes Destination types⁄ ¤ ‹ › An example of a CCR TreeCustom Call Routing P0919416 To build a CCR Tree Chapter Working with CCR TreesBuilding a CCR Tree To create a Home node Creating a Home nodeAdding nodes to the Home node To add a Menu node Adding a Menu nodeSave Print Quit To add an Information node Adding an Information nodePress END To add a Mailbox node Adding a Mailbox nodePress END To add a Transfer to an internal extension Adding a Transfer nodeTo add a Transfer to an external number About transfers to external numbersPress Othr Press Xfer ‹ or Paus Adding special characters to an external transfer numberTo assign a CCR Tree to a Greeting Table Assigning a CCR Tree to a Greeting TableDisabling a CCR Tree Testing a CCR TreeTo disable a Tree To delete a Tree Deleting a CCR TreeChanging a CCR Tree message To change a Mailbox node Changing a Mailbox nodeTo change a destination type Changing a destination typeTo change a Transfer node Changing a Transfer nodeTo delete a Path Deleting a PathPress to end the session To record and send a Broadcast message Norstar Voice Mail Chapter Broadcast and Information messagesAbout Broadcast messages To record and send a Broadcast message CallPilot About recording an Information mailbox message Information mailbox messagesTo record an Information mailbox message Recording an Information mailbox messageChapter CallPilot operations About resetting CallPilotTo reset CallPilot To initialize CallPilot Initializing CallPilotTo reset the System Administrator password Resetting the System Administrator passwordTo set the Operator status Operator settingsSetting the Operator status Resetting the Operator password Changing the Operator passwordTo change the Operator password Setting the Business Status Changing the Operator default extensionTo change the Operator default extension To assign Answer Lines Setting up line answeringTo set the Business Status To change the Automated Attendant status Setting the Automated Attendant statusLanguage availability CallPilot default system optionsTo change the Group List leading digit Group List leading digitTo enable or disable voicemail Company Directory To enable or disable the Company DirectoryTo designate the number of channels for outdialing OutdialingGeneral Delivery Mailbox To enable or disable the General Delivery MailboxTo enable a software authorization code Enabling a software authorization codeExternal Mailbox Initialization To enable or disable External Mailbox InitializationHow the Dialing Translation Table works Chapter Dialing TranslationAbout Dialing Translation Input Output Examples of Dialing Translation TablesNetwork Access To set the Dialing Translation properties Setting Dialing Translation propertiesTo build a Dialing Translation Table Building a Dialing Translation TableTo review Dialing Translation Table entries Reviewing entries in the Dialing Translation TableTo change an entry in the Dialing Translation Table Changing a Dialing Translation Table entryTo delete an entry in the Dialing Translation Table Deleting a Dialing Translation Table entryChapter Troubleshooting CallPilot Telephone cannot be forwarded to the system Verify the correct extension is assigned to the mailbox You cannot create a Group List Already a member CallPilot error messagesInvalid key Mbox not init Not recorded Ringing Answer button Chapter CallPilot configuration tipsDelayed answering by the Automated Attendant Ringing lines and answer buttonsCallPilot configuration tips Central receptionist How to set up CallPilot for different businessesCallPilot for a small business On Your Toes Dance Studio Costume Room Greeting for On Your ToesCallPilot for a medium business Bridge Stone Engineering Greeting for Bridge Stone Engineering Customer Service and Sales departmentShipping and Receiving ManagersFeature Compatibility Delayed Ring Transfer DRT Language choice Service Modes CallPilot configuration tips P0919416 Value or range Default Chapter Default configuration valuesDefault configuration values Message storage times Default configuration values P0919416 Glossary See Custom Call Routing ATA Feature code used to leave messages in CallPilot mailboxes Storage place for messages on the CallPilot system Returning CallPilot to its original default settings Push button telephone that emits Dtmf tones Glossary P0919416 Index Index Troubleshooting P0919416 Troubleshooting 113 Accessing a line or line Pool
Related manuals
Manual 149 pages 30.28 Kb Manual 68 pages 8.13 Kb Manual 68 pages 12.22 Kb
Top Page Image Contents