AT&T 1782 Connect with the Answering System, Play Messages, Connect with the answering system

Page 37

ANSWERING SYSTEM OPERATION

From a Remote Touch Tone Phone

Connect with the Answering System

1Dial your telephone number from a touch tone phone with a different telephone number.

2When the system answers, enter your three-digit Remote Access Code during or after the announcement. The system announces the number of messages, then beeps twice. If the announcement continues to play after you enter your code, wait for the announcement to end, then re-enter the code.

— OR —

Press #to stop the announcement, then re-enter the code.

3The two-beep signal lets you know the system is ready to accept a remote command.

Play Messages

1Connect with the answering system.

2After the two beeps, wait four seconds, and the system plays back messages

— OR —

Press 10to play all messages in both mailboxes

— OR —

Press 11to play all messages in the Line 1 mailbox

— OR —

Press 12to play all messages in the Line 2 mailbox

— OR —

Press 20to play only new messages in both mailboxes (if there are no new messages, the system announces,“No new messages”)

— OR —

Press 21to play only new messages in the Line 1 mailbox

— OR —

Press 22to play only new messages in the Line 2 mailbox.

NOTE: When you finish listening to messages, press *, 9before you hang up.

3To repeat a message — Press 4while the message is playing.

To repeat part of a message — Hold down 4. To resume playing, release 4. To skip a message — Press 6while the message is playing.

To skip part of a message — Hold down 6. To resume playing, release 6. To stop message playback — Press 5.

To save messages— Press *, 9then hang up.

34

Page 36 Page 38
Image 37
Page 36 Page 38
Contents USER’S Manual Advanced American Telephones. All rights reserved Page Contents Page About Softkeys ButtonsScreen Indicators Table/Desk Installation InstallationBefore You Begin Connect line cordsFor two single-line wall jacks with a single two-line phone For one two-line wall jack with two single-line phones For two single-line wall jacks with two single-line phones Connect the power cord Wall InstallationSelect display language InitializationStore Home Area Code Set Dial Mode Adjust display contrastSet the clock Set the dateFeature Setup SET UP System FeaturesSet the Time and Date Announcement Options Answering System Feature SetupRecord Outgoing Announcement for a Line Delete Outgoing Announcement for a Line Review Outgoing Announcement for a LineRing Select and Toll Saver for a Line Select Outgoing Announcement for a LineRemote Access Code for the System Answer When Recording for a LineChange Priority Call Code for the System Priority Call Signal for the SystemAudible Message Alert for the System Announcement Monitor for the SystemTurn Caller ID with Call Waiting On or Off for a Line Caller ID Feature SetupTurn Incoming Number Announce On or Off Program Area CodesLocal Area Code Guidelines Home Area Code GuidelinesLocal Area Codes Home Area CodeSet Display Screen Language Blocked Call InformationSet Dial Mode Call Match Feature SetupSet Display Contrast Caller Specific Outgoing Announcements Store a Number for Caller Specific Outgoing Announcement Record a Caller Specific Outgoing Announcement Remove a Number for Caller Specific Outgoing AnnouncementReview a Caller Specific Outgoing Announcement Delete a Caller Specific Outgoing Announcement Talking Caller IDStore a Number for Talking Caller ID Review a Talking Caller ID Announcement Record a Talking Caller ID AnnouncementDelete a Talking Caller ID Number Answering System Operation Listen to Your Messages Record a Memo Delete MessagesDelete All Messages Delete Selected MessagesRecord a Telephone Conversation When Memory is FullPlay Messages Connect with the Answering SystemConnect with the answering system Delete Selected Message Record AnnouncementChange Remote Access Code End the Remote Access CallTurn System Off Review Call History Turn System OnMemory Full Voice Help MenuIncoming Number Announce Caller ID OperationCall Waiting Caller ID OperationNEW Call Light Reviewing Call HistoryRemove Selected Call Record Removing Call Records from HistoryRemove All Call Records Making a Display Dial Call Display DialDisplay Dial Options For example Display MessagesDisplay Screen is Blank Case of DifficultyMessages are Incomplete System Does Not Answer After Correct Number of RingsPower Failure Recovery System Does Not Respond to Remote CommandsSystem Hangs Up While Using Display Dial With Speakerphone Screen Displays Extension in Use, and None AreScreen Continues to Display Lift Receiver Screen is FlashingSome of the Message is Not Audible Display Dial Doesn’t WorkUse two #4 screws Template For Wall MountingTo connect with your answering system Remote CommandsRemote Commands

1782 specifications

AT&T 1782 is a significant telecommunications switch that was deployed primarily in the late 20th century, forming an integral part of the phone network infrastructure. This technology played a crucial role in the transition from analog to digital telephony, enhancing the efficiency and reliability of communication services. The AT&T 1782 switch utilized a digital processing architecture, allowing for improved call handling capabilities and a reduction in operational costs.

One of the main features of the AT&T 1782 is its ability to support a high volume of simultaneous calls. With a digital switching capacity, it could handle numerous lines and connections without the performance degradation often seen in older analog systems. This scalability made it an attractive option for many service providers looking to expand their networks while maintaining low latency calls.

In terms of technology, the AT&T 1782 was based on time division multiplexing (TDM), a technique that divides the available bandwidth of a communication medium into time slots. This method allowed multiple signals to share the same transmission medium efficiently, ensuring optimal utilization of resources. The digital nature of the switch also facilitated easier integration with emerging technologies, paving the way for more advanced telecommunication services such as data transmission and multimedia communication.

Another characteristic of the AT&T 1782 switch was its reliability. The design emphasized redundancy and fault tolerance, which minimized downtime and improved service quality. This reliability made the switch suitable for various applications, from residential telephony to larger corporate communications.

The AT&T 1782 also supported advanced features like call routing, billing services, and maintenance monitoring. Service providers could implement these functionalities easily, allowing for personalized customer services and more efficient network management.

Overall, the AT&T 1782 embodies a critical advancement in telecommunication technology, providing the backbone for many service providers during a transformative time in the industry. Its combination of high capacity, digital processing, and reliability positioned it as a preferred choice for many communications networks, influencing how calls and data were managed for years to come.
Top Page Image Contents