Philips SE450XY/ZZ, CD450XY/ZZ, CD4502B/17 manual System

Page 46

15 The System

15.1Registering handset(s)

The procedures described below are the procedures you will find in your handset. The procedures may vary according to the handset you want to register. In this case, refer to the manufacturer's instruction of the additional handset. Additional handsets must be registered to the base station before you can use them. Your base station can register up to 5 handsets.

1 Press mon the handset you want to register.

2 Select ADVANCED SET >

REGISTER. Press OK.

3 Follow the handset's screen instruction.

• Registration shall be completed in less than 2 minutes. The base automatically assigns a handset number to the handset.

Note

If no base is found within a certain period, your handset displays a notification message. Repeat the above procedure if registration failed.

15.2Un-registering a handset Use one handset to unregister another

handset that shares the same base station. 1 Press m.

2 Select ADVANCED SET >

UNREGISTER. Press OK.

3 Select the handset (number) you want to un-register.

44

Tip

Handset Number. The handset number displays beside the handset name during standby.

5Press OK.

• The handset is un-registered.

15.3Changing your PIN

The system PIN is used for registration and protecting access rights to some of the menus. The pre-set PIN is 0000. You can personalize your PIN for greater security.

1Press m.

2Select ADVANCED SET > CHANGE PIN. Press OK.

3Enter the current system PIN. Use BACK to make corrections. Press OK to confirm the system PIN.

4Enter the new system PIN. Press OK.

5Enter the new system PIN again for verification. Press OK.

• The setting is saved.

Note

Forgotten PIN. Write down your PIN and save it for future use. If you have forgotten the PIN, reset your phone and your PIN code will be restored to the factory pre-set PIN (0000). To reset your phone, see “Restoring default settings” on page 44.

15.4Restoring default settings You can reset your phone settings to the

original factory settings.

1 Press m.

2 Select ADVANCED SET > RESET. Press OK.

The System

Image 46

Contents US Telephone Page Table of contents Extra Features Calling FeaturesNetwork Services Call logSystem Default pre-programmedSettings Technical Data Frequently asked Questions Appendix IndexImportant Safety Instructions Do not overload wall outletsIf the product’s cabinet has been damaged Power requirements Environmental Battery life may be shortened in low temperature conditionsConformity Packaging informationPage Guarantee Quick start Handset Battery doorWith Bracket Power supply NiMH AAA Rechargeable Your phoneBack/Clear key c Overview of your phone Call Log/Up key uOK key Talk/Flash key rLoudspeaker Battery door Headset jack Locate handsets Enter registration modeOverview of the base station Handset locator key Browsing the menus Display iconsMenus TipWall mounting the base CD450 Getting startedConnect the base station Getting startedRe-insert the bracket to the back of the base station Turn the bracket aroundWall mounting the base SE450 Install your handset Charge the handsets for 24 hours before initial useSelect Clock & Alarm SET DATE/TIME. Press OK Setting the clockSetting the date and time Setting the date and time formatSwitching off your handset Switching your handset onSwitching on your handset Phonebook Clock /ALARM This menu item is country-dependent Getting startedActivate Deactivate Call LOG Pre-dialing CallMaking a call Redialing the last numberEnding a call Adjusting the earpiece volumeUsing the speaker or handsfree Answering a callToggling between two external calls Press r Press OK. Select Start 2ND CALL. Press OK againYour first call will be put on hold PressTransferring a call Calling another handsetTo toggle between the calls Making a conference callDuring the conference call Press eto end the conference callExternal call is put on hold automatically Entering text and numbers Text and NumbersInput table Searching by the first character PhonebookViewing the phonebook Press OK. Select PHONEBOOK. Press OKEditing a record Setting VIP melodiesmUsing quick dialm Select Phonebook Edit ENTRY. Press OKEditing a quick dial key Cancelling a quick dial keyQuick dial key is cancelled Press m.mReturning a call Call logViewing the call records Saving a call record to your phonebookSelect DELETE. Press OK Enter and edit the name if necessary. Press OKDeleting a call record Deleting all call recordsRedial List Custom Options Select Advanced SET XHD SOUND. Press OK Calling Features Select Number Number 1 2 Activating/deactivating call barringSelect Advanced SET Call BARRING. Press OK Area code managementTurning first ring on/off This feature only applies to models with first ring supportSelect Advanced SET First RING. Press OK Network Services Select NETW. Services Call Return CALL. Press OK Editing the voicemail service numbersCalling the call return service center Editing the call return service center numberWithholding IDm Editing the cancel call back service numberSelect NETW. Services Withhold ID ACTIVATE. Press OK Activating withhold IDExtra Features Keypad lock Setting the easy call numberDeactivating easy call Locking the keypadSystem All settings have been reset Date Unchanged Date Format Default pre-programmed settingsLanguage English Handset Name XHD Sound Incoming Call Log Empty Redial List PIN Code 0000Technical Data Sound No dialing tone Connection Signal icon flashingSet-up Registration fails continuously No parking toneCheck that the handset ringer is turned on. See Phone may be at a location with thick walls. Move the baseHandset does not ring Caller ID does not displayEquipment approval Information AppendixRights of the Phone Company Appendix Please specify stock number When ordering copiesTemporary discontinuance, the telephone company must Receiving antenna is connectedHearing Aid Compatibility HAC NoiseFCC RF Radiation Exposure Statement PrivacyDo not attempt to repair or modify this equipment US / Canada Service CenterRbrc seal Entering text and numbers 27 Extra Features IndexPage