Uniden FP105 LCD Contrast, Call Wait ID ON/OFF, Reset PP Code I Clear Speed Dial I no Changes

➤LCD CONTRAST

1.Press and hold the store button for approximately 2 seconds until the display shows

LCD CONTRAST.

2.Press the >> or << buttons to adjust the display contrast to the desired viewing level.

3.Press the store button to set and move to the next menu option or cancel to save and exit.

➤TIME/DATE

1.Press and hold the store button until the display shows LCD CONTRAST.

2.Press the store button again, and the display will show SET TIME/DATE.

3.Press *(am) OR #(pm).

4.Use the keypad buttons to set the time and date manually following the cursor position.

Press the store button to set and move to the next menu option or cancel to save and exit.

Example

To set the time and date as : 08.45AM on the 9th of July 1. Use the keypad buttons and press * 0 8 4 5 8 9 0 7

2. Press the store button to set and move to the next menu option or cancel to exit,

!	If you make a mistake, use the < < or >> buttons to move the cursor and re-enter the
	correct information.
	If you subscribe to a Caller ID service, the time and date will be automaticaly updated
	when the first C/D information is received, therefore you do not need to set it manually.

➤ CALL WAIT ID ON/OFF

1. Press and hold the store button until display shows LCD CONTRAST

2. Press the store button 3 times until the display shows CALL WAIT ID ON, 3. Press the >> or << buttons to choose CALL WAIT ON/OFF

4. Press the store button to set and move to the next menu option or cancel to save and exit.

➤ RESET PP CODE I CLEAR SPEED DIAL I NO CHANGES

1. Press and hold the store button until display shows LCD CONTRAST.

2. Press the store button 4 times until the display shows RESET PP CODE. 3. Press the > > or << buttons to choose from the following options;

RESET PP CODE (Resets all pre-programmed codes to factory default), CLEAR SPEED DIAL (Deletes all stored Speed Dial memories),

NO CHANGES

4. Press the store button to confirm your choice and exit the Options Menu.

!.	The Advance User Options Menu can not be accessed if the handset is off the cradle
	or if the telephone is in the speaker phone mode.
	To exit the Advance User Options Menu at any time, press the cancel button.

If your Telephone is not performing to your expectations, please try these simple steps. If you are still unable to resolve the problems, contact Uniden Customer Service for assistance.

Problem	Suggestion
Can’t make or receive	l Make sure you use only the line cord
calls.	supplied with this telephone.
	l Check that both ends of the telephone
	line cord and Handset cord are plugged in.
Can’t hear the telephone	l Make sure you do not have too many
ringing.	telephones connected to the telephone line.
	l Adjust the Ringer Volume to either lo/hi.
	l Plug another telephone into the telephone
	socket and check for a dial tone.
Speakerphone Volume	l During speakerphone conversation, adjust
too low.	the speakervolume slider control on the side
	of the telephone.
One Touch Speed Dial	l Repeat the memory storage procedures
Numbers are not working	detailed on page 15.
correctly.
Handset does not hang	l Make sure the Handset Retainer Tab has
up in the wall mount	been turned around (point facing up)
position.	and the Handset is placed firmly into the
	cradle.
New Call LED keeps	l All new calls must be reviewed before
flashing	the new call LED stops flashing.
Message LED keeps	l Review and clear message bank messages.
flashing.
Caller ID feature not	l These are all subscription or user pays
working	services. To subscribe, or check the
Message Bank feature	pricing and availability, please contact
not working	Telstra Residential Sales and Service on
Call Diversion feature not	‘13 2200 or Telstra Business on ‘1 3 2000
working
Display information is	l This can happen due to power interruption.
incomplete or frozen.	Reset your phone by pushing the reset
	button (tiny switch located at the rear side of
	the base).

Telstrais a registered trademark of Telstra Corporation Limited ACN 051 775 556