Philips D711, D721 manual S006, Ror sR

Page 47

4.3Programming the exchange line code

If you operate your telephone on a telecommunications system with an internal S0 bus, in most cases, you must dial a digit to seize an exchange line. You can enter this digit (e.g. "0") here. This makes sure that incoming calls are stored correctly in the call list. To make absolutely sure you are doing the right thing, also consult your telecommunications system's manual.

Initial state:		idle
Steps:
No.	Description		Input	Display
1	Initiate
1	Initiate		s006	ACCESS CODE
	programming			§
	programming
				Å‹Ç¤‰ÏÌÓÛı

2	Enter the exchange
2	Enter the exchange		Z	ACCESS CODE
	line code, max.			0§
	line code, max.
	4 digits			Å‹Ç¤‰ÏÌÓÛı
	4 digits
If nec.	Clear digits singly		Ror sR	ACCESS CODE
	or completely			§
	or completely

Å‹Ç¤‰ÏÌÓÛı

3		Save the input		o

ACCESS CODE

˜*88888OK88888#·

Å‹Ç¤‰ÏÌÓÛı

4.4Enabling/disabling camp-on busy

You can enable or disable indication of calls that arrive through your con- nection during a telephone call by means of a camp-on busy tone in the handset. Then, you can either accept the call, ignore it or reject it. The caller also hears the ringing tone. The busy tone is not activated until you reject the caller.

The response may deviate from the one described here if further telephones are connected to the same S0 bus.

Note: D711 – Setting applies to MSNs 1 … 8

D721 – Setting applies to MSNs 1 … 4 (See 6.3.2.2 for MSNs 5...8)

46

Image 47

Contents SmartLine D711 Contents Programming SmartLine D721 only Emergency operation switch An emergencyAppendix Nection of an analog terminal IntroductionEasy-to-operate high-convenience Isdn telephoneGeneral 4713 For the analog port4711 4712Scope of delivery Shift key Change function level Call diversion set upOk key Start up Connector for Adapter cable SmartLine D721 onlyEstablishing and undoing a plugged connection Clears the complete line 666 8#± or ‘ Description Input Moving the cursorDial tone Chaining telephone numbers Direct call TelephoningFurther functions If necessary, change s MSN ˜1…8·§ the MSN see With the handsetOn-hook hands Free operationBer see Use a stored numNumber Chain numbersSee Dial telephonePresentation off Steps Description Input Display NumberPresentation on If previously offTelephone number Press funtilDisplayed Confirm selection EditMemory ±/‘Key, on-hook Key, number isDialled Steps Description Input Display On/off temporarily Ringing tone forBusiness call Number also from Business callW, Z Play further entries Displaying the first Most recent entry Call for MSNIf necessary, dis Nection and accept Steps Description Input Display Place the first conNection on hold End the first conRinging sounds Required entry Confirm clearing Positive ac Description Input Display Display firstCallback Scroll to Or #Activate malicious Sfpositive ac Caller identificationSteps Description Input Display Lift the handset Is stored Alter the volume Several timesCally and you hear Dial tone LevelsConversation ExchangeEnd the hold state ResumeStore the modified Volume can beDtmf digits Keypad signals Altered in nine steps Several times toStore Function during aEdit digits clear Or enter Select the MSNConfirm Description Input Display Park a callEnter the two-digit CodeEntering a number Memory Only during Call To clear the current t 345678 connection, pressPlacing a callers telephone number in the redial memory Steps Description Input Display Switch the call Mode ProgrammingWhich you wish to Divert callsDiversion is offered Quit display Or o, after Last MSN has Been displayed Input Display Adjust display con If nec. sevTrast in 11 levels Times MSN display for eachLock on or off Steps Description Input Display Switch handsetVolume between Normal and loudDescribed above Settings asPrefix, national Prefix, international No entry Redial D721Unchangedonly Off Handset volume NormalProgramming 00.00.99/0000Overview of programmable functions Ror sR S006On and off S04Is offered Next call diversionOr the complete Switch overS005 S01Identification Enter the date and ZTime Ring the call charge counter and defining the factor S008Select the required LanguageS06 S009 Confirm resetPrefix code S000S002 If nec. Clear digits singly R or sR S09Enter or edit the number If nec. Clear digits singly Ror sR S91…8S001 Private orLast digit Define ranges by Entering a dash S004Enter a blank as a Delimiter between Several schemes Prefix without S007Enter the local area Code, up to 6 digitsEnter the new PIN S03Enter the old PIN Incoming Default identificationS08 If nec. Clear digits S07Or sR 01901 toSaved S0bEntry Number input, saveSaved …9, *, #S9 1…8 Move the cursorMemories Setting can be # switched over be- tween on and offS02 Description Input Display InitiateEmergency operation …2 Not used …6 Not used Analog port SmartLine D721 onlyTerminal SmartLine D721 On the analog portMSN entry Ringing MSN entry Ringing ToneNo. Description Input Pick up ringing or Steps Description Input Initiate consultationDial the internal Users numberSecond one Put the first connection R Depending on During a conversation 1.1 PicSteps Description Depending onHas been activated Otherwise negative 37#Activating automatic callback on busy #43# #37#43# #61 #21Repeat the new New Confirm it by #67#Old Enter the new New Confirm it by Check lock #33Description Input Display Select the full lock Code *1# Apply the IsdnSeconds after Lifting the handset #53#Without dialling Destination No. # Check connection Without dialling Input within73/23/EEC Low-voltage Guideline Appendix700 Ohm When using pulse diallingKey Flash 50 ms … 350 ms Ringing voltage S09 S00 S001 S04 S05 S06 S07S002 S004 S005 S006 S007 S008 S009 S000 S0b S0w S0r Resetting the unit Reset Programming call pick up D721 onlyAccepting 53, 70 Conference 29, 38 ConnectingEditing mode Example configuration Number identificationTone ringing Tones Volume Plug-in connection Power failureRedial memory 20, 34, 37 Reset Ringing tone SwitchingPage Page PB Eindhoven Edition 11/99 Postbus