Philips D721, D711 manual Emergency operation

Page 68

5Emergency operation

5.1Emergency operation switch

Emergency operation commences in the event of a power failure. Connected to an NTBA in the emergency mode, the S0 bus can only power a terminal that is capable of emergency operation. If you are operating several terminals on the bus, the emergency mode must only be activated on one of the terminals.

Switching to the emergency mode

Remove all plugs from the terminal.

Take a screw driver and turn the switch to position 1.

Mark this terminal as the emergency terminal

Note:

When delivered, your telephone is not set to emergency operation.

1

2

1

2

Switch setting

1

2

Emergency operation possible

Emergency operation not possible

5.2In an emergency

If the power supply on your NTBA should fail, only the terminal set to the emergency mode will operate on the bus. All calls for the bus will be signalled at this one telephone. When you are making telephone calls, the emergency mode is indicated by a "!" between the date and the time on the display.

SmartLine D721:

The analog port is not available during emergency operation.

67

Image 68

Contents SmartLine D711 Contents Programming Emergency operation switch An emergency SmartLine D721 onlyAppendix Introduction Easy-to-operate high-convenienceIsdn telephone Nection of an analog terminalGeneral For the analog port 47114712 4713Scope of delivery Shift key Change function level Call diversion set upOk key Connector for Adapter cable SmartLine D721 only Start upEstablishing and undoing a plugged connection 666 8# ± or ‘Description Input Moving the cursor Clears the complete lineDial tone Telephoning Chaining telephone numbers Direct callFurther functions With the handset On-hook handsFree operation If necessary, change s MSN ˜1…8·§ the MSN seeUse a stored num Ber seeChain numbers SeeDial telephone NumberSteps Description Input Display Number Presentation onIf previously off Presentation offPress funtil Displayed Confirm selectionEdit Telephone number±/‘ MemoryKey, on-hook Key, number isDialled Steps Description Input Display On/off temporarily Ringing tone forBusiness call Number also from Business callW, Z Play further entries Displaying the first Most recent entry Call for MSNIf necessary, dis Steps Description Input Display Place the first con Nection on holdEnd the first con Nection and acceptRinging sounds Description Input Display Display first CallbackScroll to Or # Required entry Confirm clearing Positive acActivate malicious Sfpositive ac Caller identificationSteps Description Input Display Lift the handset Alter the volume Several times Cally and you hear Dial toneLevels Is storedExchange End the hold stateResume ConversationVolume can be Dtmf digits Keypad signalsAltered in nine steps Several times to Store the modifiedFunction during a Edit digits clear Or enterSelect the MSN StoreDescription Input Display Park a call Enter the two-digitCode ConfirmEntering a number Memory Only during Call To clear the current t 345678 connection, pressPlacing a callers telephone number in the redial memory Steps Description Input Display Switch the call Programming Which you wish toDivert calls ModeDiversion is offered Input Display Adjust display con If nec. sev Trast in 11 levels TimesMSN display for each Quit display Or o, after Last MSN has Been displayedSteps Description Input Display Switch handset Volume betweenNormal and loud Lock on or offSettings as Described aboveD721Unchangedonly Off Handset volume Normal Programming00.00.99/0000 Prefix, national Prefix, international No entry RedialOverview of programmable functions S006 Ror sRS04 On and offNext call diversion Is offeredSwitch over S005S01 Or the completeIdentification Enter the date and ZTime S008 Select the requiredLanguage Ring the call charge counter and defining the factorS06 Confirm reset S009Prefix code S000S002 If nec. Clear digits singly R or sR S09Enter or edit the number S91…8 S001Private or If nec. Clear digits singly Ror sRLast digit Define ranges by Entering a dash S004Enter a blank as a Delimiter between Several schemes S007 Enter the local areaCode, up to 6 digits Prefix withoutEnter the new PIN S03Enter the old PIN Incoming Default identificationS08 S07 Or sR01901 to If nec. Clear digitsS0b SavedNumber input, save Entry…9, *, # S9 1…8Move the cursor SavedSetting can be # switched over be- tween on and off S02Description Input Display Initiate MemoriesEmergency operation Analog port SmartLine D721 only …2 Not used …6 Not usedSmartLine D721 On the analog port MSN entry RingingMSN entry Ringing Tone TerminalSteps Description Input Initiate consultation Dial the internalUsers number No. Description Input Pick up ringing orDuring a conversation 1.1 Pic Steps DescriptionDepending on Second one Put the first connection R Depending onHas been activated Otherwise negative 37#Activating automatic callback on busy #43# #37#43# #21 #61Repeat the new New Confirm it by #67#Old Enter the new New Confirm it by #33 Description Input Display Select the full lockCode *1# Apply the Isdn Check lock#53# Without dialling Destination No. # Check connectionWithout dialling Input within Seconds after Lifting the handsetAppendix 73/23/EEC Low-voltage Guideline700 Ohm When using pulse diallingKey Flash 50 ms … 350 ms Ringing voltage S04 S05 S06 S07 S09 S00 S001Resetting the unit Reset Programming call pick up D721 only S002 S004 S005 S006 S007 S008 S009 S000 S0b S0w S0rConference 29, 38 Connecting Editing modeExample configuration Number identification Accepting 53, 70Plug-in connection Power failure Redial memory 20, 34, 37 ResetRinging tone Switching Tone ringing Tones VolumePage Page Postbus PB Eindhoven Edition 11/99