Philips D711, D721 manual Appendix, 73/23/EEC Low-voltage Guideline

Page 79

7Appendix

7.1Approval and CE mark

The product meets the fundamental requirements of all applicable guidelines of the Council of the European Union. The specified conformity evaluation procedures have been followed.

This unit meets the requirements of the following EU guidelines:

• 89/336/EEC - EMC Guideline

–Guideline 89/336/EEC of the Council dated 3 May 1989 to harmonise the legal regulations of the member states regarding electromagnetic compatibility; amended by 91/263/EEC, 92/31/EEC, 93/68/EEC, 93/97/EEC.

• 73/23/EEC - Low-voltage Guideline

–Guideline 73/23/EEC of the Council dated 19 February 1973 to harmonise the legal regulations of the member states in relation to electrical equipment for use within certain voltage limits; amended by 92/31/EEC, 93/68/EEC.

• TTBR 3 / CTR 3 (97/346/EG) and Amendment 1(12/97)

–Commission ruling of 20 May 1997 in relation to a joint technical specification for the basic access to the Europe-wide Integrated Services Digital Network (ISDN).

• TBR 8 / CTR 8 (Version II) (1999/304/EG)

–Commission ruling of 12 April 1999 in relation to a joint technical specification for the Integrated Services Digital Network (ISDN); telephony at 3.1 kHz, interfacing condi-

tions(11/95)for handsets.

(DIN VDE 0804 - Part 100 / 06.97)

The following EU standards were applied for conformity evaluation of EMC and the low-voltage guideline:

EN 50081 – 1 (01/92)(DIN VDE 0878 - Part 22 / 04.98)

– Electromagnetic compatibility (EMC): basic interference emission standard/Part 1

EN 50082 – 1 (01/92)(DIN VDE 0839 - Part 82 - 1 / 03.93)

– Electromagnetic compatibility (EMC): basic interference immunity standard/Part 1

EN 60950 – A4 (07/96)(DIN VDE 0805 – A4 / 11.97)

– Safety of information technology equipment including electrical office machines

EN 41003

–Special safety requirements for devices intended for connection to the telecom- munications network

78

Image 79

Contents SmartLine D711 Contents Programming SmartLine D721 only Emergency operation switch An emergencyAppendix Nection of an analog terminal IntroductionEasy-to-operate high-convenience Isdn telephoneGeneral 4713 For the analog port4711 4712Scope of delivery Ok key Call diversion set upShift key Change function level Start up Connector for Adapter cable SmartLine D721 onlyEstablishing and undoing a plugged connection Clears the complete line 666 8#± or ‘ Description Input Moving the cursorDial tone Chaining telephone numbers Direct call TelephoningFurther functions If necessary, change s MSN ˜1…8·§ the MSN see With the handsetOn-hook hands Free operationBer see Use a stored numNumber Chain numbersSee Dial telephonePresentation off Steps Description Input Display NumberPresentation on If previously offTelephone number Press funtilDisplayed Confirm selection EditMemory ±/‘Dialled Key, number isKey, on-hook Steps Description Input Display Business call Ringing tone forOn/off temporarily W, Z Business callNumber also from If necessary, dis Displaying the first Most recent entry Call for MSNPlay further entries Nection and accept Steps Description Input Display Place the first conNection on hold End the first conRinging sounds Required entry Confirm clearing Positive ac Description Input Display Display firstCallback Scroll to Or #Steps Description Input Display Lift the handset Caller identificationActivate malicious Sfpositive ac Is stored Alter the volume Several timesCally and you hear Dial tone LevelsConversation ExchangeEnd the hold state ResumeStore the modified Volume can beDtmf digits Keypad signals Altered in nine steps Several times toStore Function during aEdit digits clear Or enter Select the MSNConfirm Description Input Display Park a callEnter the two-digit CodeEntering a number Placing a callers telephone number in the redial memory To clear the current t 345678 connection, pressMemory Only during Call Steps Description Input Display Switch the call Mode ProgrammingWhich you wish to Divert callsDiversion is offered Quit display Or o, after Last MSN has Been displayed Input Display Adjust display con If nec. sevTrast in 11 levels Times MSN display for eachLock on or off Steps Description Input Display Switch handsetVolume between Normal and loudDescribed above Settings asPrefix, national Prefix, international No entry Redial D721Unchangedonly Off Handset volume NormalProgramming 00.00.99/0000Overview of programmable functions Ror sR S006On and off S04Is offered Next call diversionOr the complete Switch overS005 S01Time Enter the date and ZIdentification Ring the call charge counter and defining the factor S008Select the required LanguageS06 S009 Confirm resetS002 S000Prefix code Enter or edit the number S09If nec. Clear digits singly R or sR If nec. Clear digits singly Ror sR S91…8S001 Private orLast digit Enter a blank as a Delimiter between Several schemes S004Define ranges by Entering a dash Prefix without S007Enter the local area Code, up to 6 digitsEnter the old PIN S03Enter the new PIN S08 Default identificationIncoming If nec. Clear digits S07Or sR 01901 toSaved S0bEntry Number input, saveSaved …9, *, #S9 1…8 Move the cursorMemories Setting can be # switched over be- tween on and offS02 Description Input Display InitiateEmergency operation …2 Not used …6 Not used Analog port SmartLine D721 onlyTerminal SmartLine D721 On the analog portMSN entry Ringing MSN entry Ringing ToneNo. Description Input Pick up ringing or Steps Description Input Initiate consultationDial the internal Users numberSecond one Put the first connection R Depending on During a conversation 1.1 PicSteps Description Depending onActivating automatic callback on busy 37#Has been activated Otherwise negative 43# #37##43# #61 #21Old Enter the new New Confirm it by #67#Repeat the new New Confirm it by Check lock #33Description Input Display Select the full lock Code *1# Apply the IsdnSeconds after Lifting the handset #53#Without dialling Destination No. # Check connection Without dialling Input within73/23/EEC Low-voltage Guideline AppendixKey Flash 50 ms … 350 ms Ringing voltage When using pulse dialling700 Ohm S09 S00 S001 S04 S05 S06 S07S002 S004 S005 S006 S007 S008 S009 S000 S0b S0w S0r Resetting the unit Reset Programming call pick up D721 onlyAccepting 53, 70 Conference 29, 38 ConnectingEditing mode Example configuration Number identificationTone ringing Tones Volume Plug-in connection Power failureRedial memory 20, 34, 37 Reset Ringing tone SwitchingPage Page PB Eindhoven Edition 11/99 Postbus