Philips D721, D711 manual S008, Select the required, Language

Page 52

4.10Selecting the display language

Different languages are available for display of the texts.

Initial state: idle

Steps:

	No.	Description	Input		Display
1		Initiate
1		Initiate	s008		8888SPRACHE
		programming			˜*§§deutsch§§§#·
		programming
					Å‹Ç¤‰ÏÌÓÛı

	2	Select the required	#or *		8888SPRACHE
		language			˜*§§english§§§#·
		language

Å‹Ç¤‰ÏÌÓÛı

3		Save the input		o

LANGUAGE

˜*§§§§§OK§§§§§#·

Å‹Ç¤‰ÏÌÓÛı

4.11Charges

The telephone contains one call charge counter for each MSN and one totalising counter for all telephone numbers. Depending of your network provider, charge information can be transmitted during or at the end of a call if this feature has been enabled for your connection. Accordingly, the charges for the call conducted are displayed during or after the call.

If you make use of call-by-call connections, charges are not transmitted in every single case.

4.11.1

The call charge counter can display charge units and the corresponding cash amount. You can read off the charges accumulated for each MSN or as a total. If the charge information is sent to your ISDN connection in units, you should define the corresponding factor to make sure that the accum- ulated charges will be displayed to you during or after a call.

Note: if the charge information is presented in units and the factor is set to "0", the display appears in units, or otherwise as amounts. It goes without

51

ring the call charge counter and defining the factor

Image 52

Contents SmartLine D711 Contents Programming Emergency operation switch An emergency SmartLine D721 onlyAppendix Introduction Easy-to-operate high-convenienceIsdn telephone Nection of an analog terminalGeneral For the analog port 47114712 4713Scope of delivery Ok key Call diversion set upShift key Change function level Connector for Adapter cable SmartLine D721 only Start upEstablishing and undoing a plugged connection 666 8# ± or ‘Description Input Moving the cursor Clears the complete lineDial tone Telephoning Chaining telephone numbers Direct callFurther functions With the handset On-hook handsFree operation If necessary, change s MSN ˜1…8·§ the MSN seeUse a stored num Ber seeChain numbers SeeDial telephone NumberSteps Description Input Display Number Presentation onIf previously off Presentation offPress funtil Displayed Confirm selectionEdit Telephone number±/‘ MemoryDialled Key, number isKey, on-hook Steps Description Input Display Business call Ringing tone forOn/off temporarily W, Z Business callNumber also from If necessary, dis Displaying the first Most recent entry Call for MSNPlay further entries Steps Description Input Display Place the first con Nection on holdEnd the first con Nection and acceptRinging sounds Description Input Display Display first CallbackScroll to Or # Required entry Confirm clearing Positive acSteps Description Input Display Lift the handset Caller identificationActivate malicious Sfpositive ac Alter the volume Several times Cally and you hear Dial toneLevels Is storedExchange End the hold stateResume ConversationVolume can be Dtmf digits Keypad signalsAltered in nine steps Several times to Store the modifiedFunction during a Edit digits clear Or enterSelect the MSN StoreDescription Input Display Park a call Enter the two-digitCode ConfirmEntering a number Placing a callers telephone number in the redial memory To clear the current t 345678 connection, pressMemory Only during Call Steps Description Input Display Switch the call Programming Which you wish toDivert calls ModeDiversion is offered Input Display Adjust display con If nec. sev Trast in 11 levels TimesMSN display for each Quit display Or o, after Last MSN has Been displayedSteps Description Input Display Switch handset Volume betweenNormal and loud Lock on or offSettings as Described aboveD721Unchangedonly Off Handset volume Normal Programming00.00.99/0000 Prefix, national Prefix, international No entry RedialOverview of programmable functions S006 Ror sRS04 On and offNext call diversion Is offeredSwitch over S005S01 Or the completeTime Enter the date and ZIdentification S008 Select the requiredLanguage Ring the call charge counter and defining the factorS06 Confirm reset S009S002 S000Prefix code Enter or edit the number S09If nec. Clear digits singly R or sR S91…8 S001Private or If nec. Clear digits singly Ror sRLast digit Enter a blank as a Delimiter between Several schemes S004Define ranges by Entering a dash S007 Enter the local areaCode, up to 6 digits Prefix withoutEnter the old PIN S03Enter the new PIN S08 Default identificationIncoming S07 Or sR01901 to If nec. Clear digitsS0b SavedNumber input, save Entry…9, *, # S9 1…8Move the cursor SavedSetting can be # switched over be- tween on and off S02Description Input Display Initiate MemoriesEmergency operation Analog port SmartLine D721 only …2 Not used …6 Not usedSmartLine D721 On the analog port MSN entry RingingMSN entry Ringing Tone TerminalSteps Description Input Initiate consultation Dial the internalUsers number No. Description Input Pick up ringing orDuring a conversation 1.1 Pic Steps DescriptionDepending on Second one Put the first connection R Depending onActivating automatic callback on busy 37#Has been activated Otherwise negative 43# #37##43# #21 #61Old Enter the new New Confirm it by #67#Repeat the new New Confirm it by #33 Description Input Display Select the full lockCode *1# Apply the Isdn Check lock#53# Without dialling Destination No. # Check connectionWithout dialling Input within Seconds after Lifting the handsetAppendix 73/23/EEC Low-voltage GuidelineKey Flash 50 ms … 350 ms Ringing voltage When using pulse dialling700 Ohm S04 S05 S06 S07 S09 S00 S001Resetting the unit Reset Programming call pick up D721 only S002 S004 S005 S006 S007 S008 S009 S000 S0b S0w S0rConference 29, 38 Connecting Editing modeExample configuration Number identification Accepting 53, 70Plug-in connection Power failure Redial memory 20, 34, 37 ResetRinging tone Switching Tone ringing Tones VolumePage Page Postbus PB Eindhoven Edition 11/99