LG Electronics IP LDK-20 PRU2 Polarity Reversal detection Unit, PRCPTU2 PR and CPT detection Unit

Page 42

IP LDK-20 Installation Manual

Board Installation

 

 

3.3.3.2 Add-On Boards

PRU2 (Polarity Reversal detection Unit)

Description

The PRU2 can be optionally mounted on CBIB, and provides Polarity Reversal detection for call metering. It also provides four on-hook connection paths for SMS.

PRCPTU2 (PR and CPT detection Unit)

Description

The PRCPTU2 can be optionally mounted on CBIB, and provides four polarity reversal detection for call metering, four call progress tone detection to support the ACNR feature (Automatic Called Number Redial). It also provides four on-hook connection paths for SMS.

CPCU2 (FSK CID, PR and CPT detection Unit)

Description

The CPCU2 can be optionally mounted on CBIB, and provides four polarity reversal detection units for call metering, four call progress tone detection to support the ACNR feature (Auto Called Number Redial), and four FSK CID signal detection. It also provides four on-hook connection paths for SMS.

Figure 3.3.3.2 CPCU4

38

Image 42
Contents IP LDK-20 Installation Manual IpldkIssue Date Contents of Changes Remark Revision HistoryTable of Contents Troubleshooting Important Safety Instructions IP LDK-20 Installation Manual IntroductionPrecaution Expansion Module Installation KSU InstallationBoard Installation TroubleshootingSystem Connection Diagram IP LDK-20 System highlightsSystem Components Specifications General specificationsDescription Specification IP LDK-20 Installation ManualIntroduction System CapacityDescription CAPACITY/BOARD Total Installation precautions Pre-InstallationSafety installation instructions Wiring precautionsPower cord KSU InstallationKey service unit Mounting template UnpackingKSU exterior and dimension 2 KSU exterior and dimensionKSU with expansion module exterior and dimension 3 KSU with expansion module exterior and dimensionOpening and closing the front cover Opening the front coverClosing the front cover 4.2 Closing the front coverFrame ground connection 5 Grounding the KSUPower Supply Unit PSU installation Range of Input Voltage Connect to Fuse RatingsExternal backup batteries installation 7 External Back Up Battery InstallationKSU mounting Wall mounting8.1b KSU Wall Mounting ※ Note Be careful not to drop the KSU Rack mounting 8.2a Rack BracketInstallation of the Boards IP LDK-20 Installation Manual Board InstallationMbub Main Board Unit 2a MbubConnector/Modular Jack/Switch Functions SWITCH/CONNECTOR Functions RemarkModular JackMJ1~MJ3 Pin Assignment Mbub MJ1COTX+ Line no RJ45 Type Jack Terminating Resistors SwitchSwitch and Connector SW7Mbub MJ2 & MJ3Extension 1.3 MJ4 Pin Assignment 1.4 SW3 Functions and LED IndicationsMbub Connector PIN Number Signal Name Function 1.5 CN22 Pin assignmentIP LDK-20 Installation Manual Board Installation Lcob CID Loop Start CO line Interface Board Installation of the CO Line BoardBoard Port Connector Type Description Cable Remark LcobAdd-On Boards Connector FunctionsPin Assignment Function Remark1.2b PRCPTU4 CPCU4 FSK CID, PR and CPT detection Unit Stib Basic Rate Interface Board Selectable S/T interface 2 StibCN1 ModeTX+ RX+ OFF SW4 SW1Isdn terminal TE1or TA Stib Port1 OnlyCN1 SW2 LED Indications StatusMJ1 SW4 Line Connector and Terminating ResistorsOr S Switch Setting MJ1 SW1Cbib CID Loop Start CO line + Basic Rate Interface Board 3 CbibCbib 1’ST Port for BRI T-MODE PIN Number Signal Name FunctionVarious Connectors Functions Cbib 2’ND Port for LCOPRU2 Polarity Reversal detection Unit PRCPTU2 PR and CPT detection UnitCPCU2 FSK CID, PR and CPT detection Unit Board Installation of the Extension BoardDTIB4 Digital Terminal Interface Board DKTDTIB8 Digital Terminal Interface Board 2 DTIB8SLT-TIP SLIB4 Connector PIN Number Signal NameSLIB4 Single Line Interface Board SLTSLIB8 Connector PIN Number Signal Name SLIB8 Single Line Interface BoardOther Board Installations Vmibe Voice Mail Interface Board EnhancedRECORD/PLAY MOH Max record time AAFBEAuto Attendant Function Board EnhancedChannel System/time stampLanu Connector PIN Number Signal Name Function Lanu LAN interface UnitLED Indication of MJ1 Meaning Modu Modem function Unit 4 ModuUnpacking Module Port Connector Description Cable Remark TypePower Cord Battery Cable Module Fuse DtimOpening and closing the front cover Opening the front coverClosing the front cover 2 Closing the front coverConnecting Expansion Module to KSU 1 Connecting an expansion moduleWall mounting Rack Mounting 3.1 Rack bracket3.4 Module Rack Mounting External backup batteries connection External Back Up Battery Installation1 Voim Various switches and connectors functions Switch / Connector Functions RemarkLED indications Signal Name FunctionPin assignment LED2.1 Voiu Installation VOIUVoice over Internet Protocol Interface UnitSlimslt Interface Module Installation 1 SlimDTIMDigital Terminal Interface Module 1 DtimTerminal Models Model DescriptionTerminal Cabling Distance Terminal Cabling DistanceDigital Keyset Connector Type PIN Number Signal NameKeyset Connection 2 SLTExternal Paging wiring Connecting Additional TerminalsExternal Music Source wiring Alarm Detection wiringBefore Starting the IP LDK-20 System Basic PreprogrammingDktu Station 10 programming LCD Button explanationSoft Button Ring LEDResetting the System Entering programming modePermanent Update Procedure To enter Programming Mode, perform the following StepsPre-programming Site NameKeyset Map International Calling Codes CodeCIS STA Code COL STA & COL Number Plan Type Number SET Type Intercom Default RemarkNumbering Plan Type PGM RangeNumbering Plan Detail Station Numbers DescriptionTRANS/PGM + Plan a Flex Default ValueFlexible Numbering Plan PGM Flex Numbering Plan ApgmFlex Numbering Plan B PGM IP setting for System PGM Cause / Symptom Solution IP LDK-20 Installation Manual TroubleshootingProblem MOH