Panasonic KX-TG2551ALS, KX-TG2551NZS Battery Replacement, Few minutes, Then install the new one

Page 47

Battery Replacement

If “Recharge” is displayed and/or “

 

 

 

” flashes after a few telephone

 

 

 

calls even if the battery was fully charged, replace the battery with a new Panasonic N4HKGMB00001 (P-P510) battery.

1

Press the notch on the battery cover

firmly and slide it as indicated by the

arrow.

2

Remove the old battery and wait for

 

a few minutes.

 

 

Then install the new one.

 

 

•Insert the battery plug into the

 

 

connector as shown.

 

 

•Be sure wires are free from being

 

 

pressed by the battery body or the

 

 

handset cover.

Red

 

Black Lead

 

Black

Lead

 

Lead

 

3

Close the cover. Make sure the handset display shows “

 

 

 

”,

 

 

 

when you place the handset on the base unit.

 

 

•If it does not show “

 

 

 

”, remove the new battery and wait for 10

 

 

 

 

 

 

 

 

 

 

 

 

minutes; and then insert the battery again. Make sure the handset display

4

shows “

 

 

 

”.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Charge the new battery for about 6 hours in order to display the

battery strength prompt correctly (p. 11).

 

Useful Information

47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Operating Instructions Charge the battery for about 6 hours before initial useFor your future reference Accessories includedBefore Initial Use Base Unit Location/Noise Battery ChargeFor Best Performance Contents Call Waiting and Caller ID Compatible For Australia only Useful InformationHandset How to use the Navigator keyLocation of Controls Hook p Antenna p Charge Contacts p Caller ID Indicator pIndicator p Base unit0266667777 Display0355566677 1120A JAN10 Connections SettingsFully charged Medium Low flashing Needs to be recharged Battery strengthDisplay prompt Battery strength Operation Operating time Battery informationStandby mode While the handset is off the base unit RechargeSelecting the Line Mode During programming Programmable FunctionsLCD contrast To select the LCD contrast p Press Ö or Ñ to select On or Off Setting the Auto Talk FeatureTo turn the ringer ON, press Ñ or Ö Selecting the Ringer VolumeContrast Selecting the LCD ContrastPoints to LCD contrast Press Ö or Ñ to select the desiredTo redial the last number dialled Making CallsIf noise interferes with the conversation To increase, press Ñ To decrease, press Ö To dial after confirming the entered numberTo redial after confirming the last number dialled Backlit LCD display Answering CallsAuto Talk Lighted handset keypadPrivate name display Caller ID ServiceHow caller information is displayed when a call is received While the handset is off the base unit To check the number of new callsFor New Zealand Users While the handset is on the base unitViewing the Caller List Using the Caller ListDisplay meaning Ex. When you search from the most recent callTo return to the previous caller To exit the Caller ListPress Ö or Ñ repeatedly to find Calling Back from the Caller ListLift the handset off the base unit Press Ö or Ñ to enter the Caller ListFree editing Editing the Caller’s Phone NumberYou can edit a phone number in the Caller List Storing Caller List Information in the Directory When the caller’s name is not displayed in the Caller ListTo erase a specific caller from the Caller List Erasing Caller List InformationTo erase all entries in the Caller List Storing a Phone Number in the Direct Button One-Touch DiallerDialling the Stored Number in the Direct Button Storing Names and Numbers in the Directory Using the DirectoryDialling buttons p Enter a name, up to 15 characters usingNumber of times key is pressed Keys Selecting Characters to Enter NamesIf you make a mistake while entering a name Eight times When finished, press Ö Next keyFor example, to enter Tom Jones While the arrow points to SaveTo search for a name by initial Finding Items in the DirectoryKeys Index Dialling from the DirectoryIndex table Editing an Item in the Directory Press FWD/EDIT á Yes key or Clear Erasing an Item from the DirectoryDirectory item you want to erase Handset Locator Special FeaturesHow to Use the Pause Button Automatic Security Code SettingFor Australia only For Call Waiting Service Users in New ZealandCall Waiting and Caller ID Compatible Desired time is displayed Recall ButtonSelecting the recall time Points to Recall timeAdding Another Phone Push it in the direction of the arrow Wall MountingTuck the telephone line cord inside Wall mounting adaptor, thenTo charge the handset battery Connection an optional headset to the handset Using the Belt ClipUsing an Optional Headset To attach the belt clip To remove the belt clipFew minutes Battery ReplacementThen install the new one Battery strength prompt correctly pProblem TroubleshootingTry again Have been pressed when you picked upHandset. Press FUNCTION/EXIT/CH Be redialled correctly Recharge is displayed on Charge the battery fully pHandset is too far from the base unit Than 32 digits long, the number will notFor New Zealand Customers For Australian CustomersPlacement Safety InstructionsSafety Installations EnvironmentMedical Specifications Instructions to customer InstallationImportant Information For Australia only PQQX13462ZA-BM S0802-0 Service difficulties
Top Page Image Contents