Panasonic KX-TG7851TU Programmable settings, Display the menu tree and direct command code table

Page 21

Programming

Programmable settings

You can customise the unit by programming the following features using the handset. To access the features, there are 2 methods.

nScrolling through the display menus 1 MN (right soft key)

2 Press MCN, MDN, MEN, or MFN to select the desired main menu. a MOKN

3 Press MCN or MDN to select the desired item from the next sub-menus. a MOKN

4 Press MCN or MDN to select the desired setting. a MOKN

R This step may vary depending on the feature being programmed. R To exit the operation, press MeN.

nUsing the direct command code

1 MN (right soft key) a Enter the desired code. Example: Press MN (right soft key) #101.

2Select the desired setting. a MOKN

R This step may vary depending on the feature being programmed. R To exit the operation, press MeN.

Note:

RIn the following table, < > indicates the default settings.

RIn the following table, indicates the reference page number.

RDisplay menu order and sub-menu may vary depending on your model.

Display the menu tree and direct command code table

Main menu: “Time Settings”

Sub-menu 1	Sub-menu 2	Settings	Code
Set Date/Time*1	–	–	#101	13
Memo Alarm	1-3:Alarm1-3	1: Once	#720	24
		2: Daily
		3: Weekly
		0: <Off>
Time Adjustment1, 2	–	1: Caller ID	#226	–
		0: <Manual>

Main menu: “Caller List”

Operation	Code
Viewing the caller list.	#213	29

Main menu: “Intercom”

Operation	Code
Paging the desired unit.	#274	32
		21

TG7851TU(en-en)_0718_ver011.pdf 21

2013/07/18 12:00:00

Image 21

Contents Thank you for purchasing a Panasonic product Digital Cordless PhoneTable of Contents Supplied accessories Accessory informationAdditional/replacement accessories Expanding your phone systemDeclaration of Conformity General informationFor your safety Battery Important safety instructionsFor best performance Base unit location/avoiding noiseOther information SpecificationsRoutine care For business users in the European UnionRF transmission power Frequency rangeOperating conditions Battery installation Setting upConnections Base unitDuring a power failure Battery chargingBattery level Icon Battery levelControls HandsetBase unit Handset display items DisplayHandset soft key icons Handset main menu iconsScreen saver mode Turning the power on/offInitial settings One touch eco mode Display modeProgramming the display mode beforehand Answering calls Making callsUseful features during a call Handset equalizer Key lockCall share MbN Equalizer a MoknShared phonebook MbN Phonebook a Mokn Speed dial Display the menu tree and direct command code table Programmable settingsNight Mode Ringer Setup Ringer VolumeStart/End Night Mode 30 sec Time Settings Set Date/Time*1Dial Mode *1 Pulse Line SetupMsec # 160 msec Privacy Mode *1, *10 Repeater Mode *1Special programming Alarm#173 Off Main menu Operation Code Storing/Viewing bar call numbers #217Turning night mode on/off Night modeSetting the ring delay Changing the start and end timeChanging the handset name Setting call restrictionIncoming call barring Caller ID subscribers only Storing unwanted callersOperating additional units Registering a unitRegistering a handset to the base unit Additional handsetsSetting the repeater mode Increasing the range of the base unitDect repeater Caller ID features Using Caller ID serviceCaller list Viewing the caller list and calling backErasing selected caller information Erasing all caller informationStoring caller information to the phonebook Voice mail service Intercom Handset locatorTransferring calls, conference calls Character entry modes Character entryExtended 1 character table Extended 2 character tableCyrillic character table Error messages Cause/solutionDisplay message Programmable settings TroubleshootingProblem General useMaking/answering calls, intercom Battery rechargeLiquid damage Caller IDIndex TU-1/2 For your future referenceAttach your purchase receipt here