Firstech, LLC 2WSHLCD-5P, 2W900FMR-2ND-5P manual General System Functions, Shock Sensor Bypassed

Page 11

Remote LCD(liquid crystal display) Diagram and lcons

aŒ’@iƒŽ“M

 

Shock Sensor Bypassed

 

This icon will be displayed when the shock sensor is bypassed by pressing buttons I+III for 2.5 sec. Impact to the vehicle will not be

 

detected at this time. This icon is always displayed on starter only systems because there is no shock sensor.

Not

Voltage

Available

This icon will be displayed while the remote is reporting the voltage of the vehicle or remote battery.

 

Temperature

 

This icon will be displayed while the remote is reporting the temperature of the vehicle.

 

 

General System Functions

The remote transmitter functions have been predetermined and programmed from the factory. The four button configuration allows for many functions to be performed through a series of tapping, holding and / or multiple presses of buttons. Although CompuStar remotes have numerous button functions and capabilities, please keep in mind that the most common functions are performed in one simple step.

Sending Commands

When in range, and a command has been sent, the remote pager backlight will illuminate, the remote will beep and the appropriate icon will be displayed. For example, to send a remote start command from the pager, hold down button (II) for 2.5 seconds. The backlight will illuminate and the remote will beep once to confirm the command has been sent and that the remote is in range. Once the vehicle has successfully remote started, the remote will receive a command indicating the vehicle is running.

Receiving Commands

The remote pager will receive commands indicating the status of the vehicle, confirmation of sending commands and alarm notifications. For example, after sending the lock command, the pager will be updated with the lock icon to confirm the vehicle has been successfully locked/armed. To see if your pager is in range to receive commands, tap button (IV) for 0.5 seconds - if the pager backlight illuminates and beeps, the pager is in range to receive commands.

ByFirstech,LLC

 

20

21

 

ByFirstech,LLC

 

 

Image 11
Contents Toll Free 21911 68th Ave S Kent, WA RwYPPfmrMRŽ„MUp RwshlcdMUp‚Œ…@o†@cŽ”…Ž”“ Introduction Kits ContentsWarranty Coverage Remote Reference Remote Reference…”…@m‰Ž”…ŽŽƒ…Mb””…’™@r…Œƒ……Ž” Quick ReferenceŒ…”@m„… Rw™@r…”…@b•””Ž@f•Žƒ”‰Ž“ ’‡’‰Ž‡@”ˆ…@cŒƒ‹@Hlcd@r…”…@oŽŒ™IRequired Qw™@r…”…@b•””Ž@f•Žƒ”‰Ž“ Option programming menu 2 Installers Only Remote LCDliquid crystal display Diagram and lcons”’”…’@iƒŽ“M Ž@iƒŽ“M„–Žƒ…„@iƒŽ“M Œ’@iƒŽ“MShock Sensor Bypassed General System FunctionsŽ•Œ@t’Ž“‰““‰Ž@r…”…@s”’”@f•Žƒ”‰Ž@Hr…“…’–”‰Ž@m„…I ƒ”‰–…@lƒ‹Oa’@Ž„@uŽŒƒ‹Od‰“’““‰–…@lƒ‹Oa’ •””‰ƒ@t’Ž“‰““‰Ž@r…”…@s”’”@f•Žƒ”‰Ž•˜‰Œ‰’™@o•”•”“@O@w‰Ž„—@rŒŒMd—Ž@O@sŒ‰„‰Ž‡@d’“ ’•Ž‹@r…Œ…“…ˆƒ‹@s…Ž“’@oŽOo†† ……’”•’…@Ž„@b””…’™@q•…’™‰Œ…Ž”@a’@O@d‰“’ …”…@m•”…@O@v‰‚’”‰Ž@m„…Ž„ c’@m„…@Hm•Œ”‰Œ…@v…ˆ‰ƒŒ…@cŽ”’ŒI Advanced System Functions’‰–…@lƒ‹@O@i‡Ž‰”‰Ž@cŽ”’ŒŒ…„@d’@lƒ‹“ •’‚@t‰…’@m„…Rps@Hr…”…@p‡‰Ž‡@s…Ž“’I@uŽŒƒ‹@O@d‰“’ ’@cŒŒ@O@rps@Hr…”…@p‡‰Ž‡@s…Ž“’I‰…’@s”’”@m„… …ƒ•’…@vŒ…”@s—‰”ƒˆŽ”‰@jƒ‹‰Ž‡@m„…@ Œ„@O@h”@s”’”@m„…•”@m„… ’‡’‰Ž‡@@RwYPPfmrMRŽ„MUp Remote Start Error DiagnosticRemote Coding / Programming Routine S Limited Lifetime Warranty Alarm DiagnosticYour Warranty ByFirstech,LLC