Uniden UIP 160P owner manual Install the rechargeable battery pack into the handset

Page 13

Install the rechargeable battery pack into the handset

1) Press down on the handset battery case cover (use the finger indention for a better grip) and slide the cover downward to remove.

2) Plug the battery pack connector (red & black wires) into the jack inside the battery compartment. (The connector notches fit into the grooves of the jack only one way.)

Match the wire colors to the polarity label in the battery compartment, connect the battery and listen for a click to insure connection.

3) Make sure you have a good connection by slightly pulling on the battery wires. If the connection is secure, the battery jack will remain in place.

4) Place the battery case cover back on the handset and slide it upwards until it clicks into place.

5) Place the handset in the base with the keypad facing forward.

6) Make sure that the charge LED illuminates. If the LED does not illuminate, check to see that the AC adapter is plugged in and the handset makes good contact with the base charging contacts.

7)Charge the handset battery pack for at least 15-20 hours before using your new cordless handset for the first time.

note

•Use only the Uniden (BT- 446) rechargeable battery pack supplied with your cordless telephone.

•Replacement battery packs are also available through the Uniden Parts Department (see back cover page).

S E T T I N G U P T H E P H O N E

w w w . u n i d e n . c o m

S E T T I N G U P T H E P H O N E [ 1 2 ]

Image 13

Contents Series Owners Manual Contents Welcome Features Accessibility VoIP TerminologyRedial/p/vol Controls & FunctionsBase Charging Contacts Reset switch Base Antenna Safety Recommendations Setting up the PhoneCheck Your Equipment Service NoticeCheck Your Broadband Configuration Do not connect the UIP160P to a regular telephone wall jack Activate your Packet8 Service Install the rechargeable battery pack into the handset Ten Handset Expandability Expanding Your PhoneRegister the Handset De-register the Handset Headset Installation Installing the BeltclipTo attach the beltclip To remove the beltclipDisplay and Icons Example of the standby mode displayTalk mode Standby modeSoft Key Function Main Menu Options Default SettingsUsing the interface Setting Menu OptionsHandset Setup Selecting a Ringer VolumeSelecting a Ringer Tone Setting AutoTalk Distinctive Ring SetupSetting the True Banner Setting Anykey AnswerSelecting a Language Adjusting the LCD ContrastSetting the Key Touch Tone Setting the Animation Screen Find Handset Paging the Handset Setting Day and Time Global SetupSetting the Area Code Setting Cidcw Caller ID on Call WaitingCalling with Packet8 service Using Your PhoneUsing the Speakerphone To set AutoTalk, see page 22 or to set Anykey Answer see Making and Receiving CallsPlacing a Call on Hold Call WaitingDeleting a Redial Record Redialing a CallTemporarily Muting the Ringer Adjusting the Earpiece and Speaker VolumeStoring a Redial Record Mute Microphone Privacy ModeTraveling Out of Range Find Handset ConferencingResetting the New Message LED Using One Touch Voice Mail AccessPress the Store soft key. Store/Edit Name appears Speed Dial appears. Press cid/vol/∧ or redial/p/vol/∨ Chain DialingNumber of times key is pressed Steps for Entering Names and Special CharactersIf you make a mistake while entering a name Viewing the Phonebook From Standby Mode Making Calls Using the PhonebookFrom Talk Mode Speed DialingDeleting the Stored Data Editing or Erasing a Phonebook EntryQrkpi Copying Phonebook EntriesCaller ID and Cidcw Caller ID on Call Waiting Packet8 service comes with Caller ID and Call WaitingViewing the Caller ID List Deleting a Caller ID Record Calling a party from the Caller ID list Standby mode Using the Caller ID Message ListDeleting All Caller ID names/numbers Storing Caller ID records in the Phonebook Talk modeUsing the DirectLInk Two-Way Radio Feature Multi-Handset FeaturesActivating DirectLink Mode L T I H a N D S E T F E a T U R E S 5 Making a DirectLink CallUsing the Room/Baby Monitor Using the Intercom Transferring a Call Getting Help TroubleshootingUnderstanding the LED Indicators Installation TroubleshootingLED Statuses and Their Meaning Power Cycle Resetting the UIP160PHard Reset Logging into the UIP160P Local Area ResetFor Terminal Adapter Features Common IssuesFor Telephone Features Symptom Suggestion Charge the battery pack for 15-20 hours Power Failure Battery replacement and handlingCleaning the battery charging contacts Battery LifeLow battery alert General Information Battery InformationAC Adapter Information Case Action Liquid DamagePrecautions Radio Equipment Numerics IndexKTGEV.KPM/QFG Main Menu Flow ChartI N M E N U F L O W C H a R T 7 Need a Part? Help for our Special Needs Customers Page Register Online Today