Panasonic DMR-E75V operating instructions TV operation, Remote Setting, Press Return

Before Use

TV operation

You can control TVs by entering the remote control code.

Preparation

≥Turn on the TV.

[1]Refer to the chart below for the code for your TV.

[2]Press and hold [TV, Í] and enter the 2-digit

code with the numeric buttons.

≥e.g.: “01”: [0] )[1].

≥After entering the code, test the remote control by turning on the TV and changing channels.

List of TVs Compatible with the unit’s Remote Control Manufacture and Code No.

Note

≥If there is more than one code, repeat the procedure until you find the code that allows correct operation.

≥If your TV brand is not listed or if the codes listed here do not allow control of your TV, this remote is not compatible with your TV.

Operation:	Button
On and off:	[TV, Í]
Video input mode:	[TV, AV]
Channels:	[TV, CH, W, X]
Volume:	[TV, VOLUME, i, j]

Panasonic	01, 02, 03, 04, 44	GOODMANS	05, 06, 31	NOKIA	25, 26, 27	SANYO	21
AIWA	35	GRUNDIG	09	NORDMENDE	10	SBR	06
AKAI	27, 30	HITACHI	22, 23, 31, 40, 41, 42	ORION	37	SCHNEIDER	05, 06, 29, 30, 31
BLAUPUNKT	09	INNO HIT	34	PHILIPS	05, 06	SELECO	06, 25
BRANDT	10, 15	IRRADIO	30	PHONOLA	31, 33	SHARP	18
BUSH	05, 06	ITT	25	PIONEER	38	SIEMENS	09
CURTIS	31	JVC	17, 39	PYE	05, 06	SINUDYNE	05, 06, 33
DESMET	05, 31, 33	LOEWE	07	RADIOLA	05, 06	SONY	08
DUAL	05, 06	METZ	28, 31	SABA	10	TELEFUNKEN	10, 11, 12, 13, 14
ELEMIS	31	MITSUBISHI	06, 19, 20	SALORA	26	THOMSON	10, 15
FERGUSON	10	MIVAR	24	SAMSUNG	31, 32, 43	TOSHIBA	16
GOLDSTAR/LG	31	NEC	36	SANSUI	05, 31, 33	WHITE	05, 06
						WESTINGHOUSE

ªSwitching to the AV input on your Panasonic TV

≥Press [AV] to switch to the AV input. Each press of [AV] switches between “TV reception” and “AV input(s)”.

Remote Setting

If other Panasonic products are placed close together, change the remote control code on the main unit and the remote control (the two must match).

≥Use “MODE 1”, the factory set code, under normal circumstances.

Preparation

≥Press [DVD].

[1]While stopped

Press [FUNCTIONS].

[2]Select “SETUP” with [3, 4, 2, 1] and press [ENTER].

[3]Select “Others” with [3, 4] and press [2, 1].

[4]Select “Remote Control” with [3, 4] and press [ENTER].

[5]Press [3, 4] to select the code (MODE 1,

MODE 2 or MODE 3) and press [ENTER].

The code on the unit has been set.

[6]While pressing [ENTER], press and hold for about 2 seconds the numeric button ([1], [2], or [3]) corresponding to the code you selected in

step 5.

The code on the remote control has been set.

[7]Press [RETURN].

When the following display appears when you use a remote control with a different code.

The unit’s remote control code

If you are trying to use this unit’s remote control, change its code to match the unit’s (# step 6).

11