Heat Controller HMH30AS-1 manual How to mount installation plate, Drill a hole in the wall, Indoor

Page 5

How to mount installation plate

The wall you select should be strong and solid enough to prevent vibration

AMount the installation plate on the wall with four type A screws. If mounting the unit on a concrete wall, use anchor bolts.

■Mount the installation plate horizontally by aligning the centerline using a level.

Installation Plate

Type "A" screw

BMeasure the wall and mark the centerline. It is also important to use caution concerning the location of the installation plate-routing of the wiring to power outlets is through the walls typically. Drilling the hole through the wall for piping connections must be done safely.

Drill a hole in the wall

■Drill the piping hole with a ø 70mm(0.0028in) hole core drill. Drill the piping hole at either the right or the left with the hole slightly slanted to the outdoor side.

	WALL
Indoor	Outdoor

5-7mm

(0.2~0.3")

Left rear piping

50mm(2.0in)

Right rear piping

115mm(4.5in)

180mm	ø 70mm(2.8in)
(7.1in)

Image 5

Contents HMC30AS-1/HMH30AS-1, HMC30BS-1/HMH30BS-1Single-Zone Refer to Installation OverviewFor right rear piping Two type B screwsDo not install it yourself customer Following should be Always Observed for SafetyRooftop Installations Installation of INDOOR, Outdoor UnitSelect the best location Piping length and elevationInstallation Plate Type a screw How to mount installation plateDrill a hole in the wall IndoorConnection of piping -Indoor Flaring Work and Connection of PipingFlaring work Remove the lower panel by the arrow Indoor unit installationRemove the front right side panel by the arrow Wrap the insulation material around the connecting portion Suction Evaporator Connecting cable84.2kg.m Tighten the flare nut with a wrenchSection Reinstall the parts to the original positionBad case Installation Information For left piping Good caseFor left piping. Follow the instruction below Connection of piping -Outdoor Connection of the drain hoseFollows the arrow on the wrench 30kAWG #20 Wiring must be as following diagramConnect the cable to the Indoor unit Outdoor Unit Connect the cable to the outdoor unitRemove the right side panel Checking the drainageRemove the lower panel by the arrow To check the drainage Drain pipingSeal small openings around pipings with a gum type sealer Form the pipingAir purging AIR PurgingAir purging with vacuum pump PreparationFinishing the job Soap water methodEvacuation Charging Pump Down Procedure Prepare remote controlTest Running Settlement of outdoor unitMemo Memo No A20001V

HMC30AS-1, HMH30BS-1SINGLE-ZONE, HMH30AS-1, HMC30BS-1 specifications

The Heat Controller HMC30AS-1, HMH30AS-1, HMH30BS-1 SINGLE-ZONE, and HMC30BS-1 are cutting-edge HVAC systems designed to provide optimal comfort and efficiency in both residential and commercial settings. These models embody the latest advancements in heating and cooling technology, making them ideal choices for anyone looking to enhance their indoor environment.

One of the standout features of these heat controllers is their energy efficiency. With advanced inverter technology, these products adjust compressor speed based on the heating or cooling demand, significantly reducing energy consumption compared to traditional systems. This not only lowers utility bills but also reduces environmental impact, making them a sustainable choice for eco-conscious consumers.

The HMC30AS-1, HMH30AS-1, HMH30BS-1 SINGLE-ZONE, and HMC30BS-1 also come with programmable thermostats, allowing users to set specific temperature schedules according to their daily routines. This convenience ensures that spaces are always at the desired temperature when occupied, providing a perfect balance between comfort and energy conservation.

Another impressive characteristic is their quiet operation. These systems are engineered with sound-dampening technology, minimizing noise levels and ensuring a peaceful indoor atmosphere. This is especially beneficial for bedrooms, offices, or any spaces where tranquility is essential.

Durability and reliability are also hallmarks of these models. Built with high-quality materials and robust components, they are designed to withstand varying environmental conditions while providing consistent performance. The heat controllers also come with comprehensive warranties, giving users added peace of mind regarding their investment.

In addition to their efficiency and durability, these systems offer versatile installation options. Whether it's a compact single-zone setup or a larger installation, the HMC30 series is adaptable, making it suitable for various building layouts.

With their modern design and user-friendly interfaces, these heat controllers blend seamlessly into contemporary spaces. Smart technology options enable integration with mobile apps and smart home systems, allowing for remote monitoring and adjustment.

From energy-saving features to quiet operation, the Heat Controller HMC30AS-1, HMH30AS-1, HMH30BS-1 SINGLE-ZONE, and HMC30BS-1 represent the pinnacle of heating and cooling solutions, meeting the diverse needs of today's consumers.