Heat Controller HMH30AS-1, HMC30BS-1, HMC30AS-1 Connecting cable, Suction Evaporator, 84.2kg.m

Page 9

CInsert the connecting cable into the indoor unit.

Don't connect the cable to the indoor unit.

Make a small loop with the cable for easy connection later.

DTape the drain hose and the connecting cable.

• Connecting cable

EIndoor unit installation

Hook the indoor unit onto the upper portion of the installation plate.(Engage the three hooks of the rear top and rear lower of the indoor unit with the upper edge and lower edge of the installation plate.) Ensure that the hooks are properly seated on the installation plate by moving it left and right.

Installation plate

Setting line

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Spanner (fixed)

 

Flare nut

Torque wrench

 

Connection pipe

 

 

Indoor unit tubing

 

 

Capacity

Pipe Size[Torque]

 

 

(Btu/h)

Suction

Evaporator

30k

5/8"[6.6kg.m]

3/8"[4.2kg.m]

When extending the drain hose at the indoor unit, install the drain pipe.

Drain hose

Indoor unit drain hose

Adhesive Vinyl tape (narrow)

GWrap the insulation material around the connecting portion.

Overlap the connection pipe heat insulation and the indoor unit pipe heat insulation material. Bind them together with vinyl tape so that there is no gap.

Plastic bands Insulation material

Indoor unit

Three upper hooks

Installation plate

Three lower hooks

Wrap the area which accommodates the rear piping housing section with vinyl tape.

FConnecting the pipings to the indoor unit and the drain hose to drain pipe.

Put a couple drops of refrigerant oil on the face of the flare before assembling taking care not to add any contaminants

Align the center of the pipings and sufficiently tighten the flare nut by hand.

Indoor unit tubing

Flare nut Pipings

Tighten the flare nut with a wrench.

Connection

Indoor

unit piping

pipe

 

Vinyl tape

Wrap with vinyl tape

(wide)

 

 

Pipe

 

Vinyl tape(narrow)

Connecting cable

 

9

Image 9
Contents HMC30AS-1/HMH30AS-1, HMC30BS-1/HMH30BS-1Single-Zone Refer to Installation OverviewFor right rear piping Two type B screwsDo not install it yourself customer Following should be Always Observed for SafetyRooftop Installations Installation of INDOOR, Outdoor UnitSelect the best location Piping length and elevationInstallation Plate Type a screw How to mount installation plateDrill a hole in the wall IndoorFlaring Work and Connection of Piping Flaring workConnection of piping -Indoor Indoor unit installation Remove the front right side panel by the arrowRemove the lower panel by the arrow Wrap the insulation material around the connecting portion Suction Evaporator Connecting cable84.2kg.m Tighten the flare nut with a wrenchSection Reinstall the parts to the original positionInstallation Information For left piping Good case For left piping. Follow the instruction belowBad case Connection of piping -Outdoor Connection of the drain hoseFollows the arrow on the wrench 30kWiring must be as following diagram Connect the cable to the Indoor unitAWG #20 Outdoor Unit Connect the cable to the outdoor unitRemove the right side panel Checking the drainageRemove the lower panel by the arrow To check the drainage Drain pipingSeal small openings around pipings with a gum type sealer Form the pipingAir purging AIR PurgingAir purging with vacuum pump PreparationSoap water method EvacuationFinishing the job Charging Pump Down Procedure Prepare remote controlTest Running Settlement of outdoor unitMemo Memo No A20001V

HMC30AS-1, HMH30BS-1SINGLE-ZONE, HMH30AS-1, HMC30BS-1 specifications

The Heat Controller HMC30AS-1, HMH30AS-1, HMH30BS-1 SINGLE-ZONE, and HMC30BS-1 are cutting-edge HVAC systems designed to provide optimal comfort and efficiency in both residential and commercial settings. These models embody the latest advancements in heating and cooling technology, making them ideal choices for anyone looking to enhance their indoor environment.

One of the standout features of these heat controllers is their energy efficiency. With advanced inverter technology, these products adjust compressor speed based on the heating or cooling demand, significantly reducing energy consumption compared to traditional systems. This not only lowers utility bills but also reduces environmental impact, making them a sustainable choice for eco-conscious consumers.

The HMC30AS-1, HMH30AS-1, HMH30BS-1 SINGLE-ZONE, and HMC30BS-1 also come with programmable thermostats, allowing users to set specific temperature schedules according to their daily routines. This convenience ensures that spaces are always at the desired temperature when occupied, providing a perfect balance between comfort and energy conservation.

Another impressive characteristic is their quiet operation. These systems are engineered with sound-dampening technology, minimizing noise levels and ensuring a peaceful indoor atmosphere. This is especially beneficial for bedrooms, offices, or any spaces where tranquility is essential.

Durability and reliability are also hallmarks of these models. Built with high-quality materials and robust components, they are designed to withstand varying environmental conditions while providing consistent performance. The heat controllers also come with comprehensive warranties, giving users added peace of mind regarding their investment.

In addition to their efficiency and durability, these systems offer versatile installation options. Whether it's a compact single-zone setup or a larger installation, the HMC30 series is adaptable, making it suitable for various building layouts.

With their modern design and user-friendly interfaces, these heat controllers blend seamlessly into contemporary spaces. Smart technology options enable integration with mobile apps and smart home systems, allowing for remote monitoring and adjustment.

From energy-saving features to quiet operation, the Heat Controller HMC30AS-1, HMH30AS-1, HMH30BS-1 SINGLE-ZONE, and HMC30BS-1 represent the pinnacle of heating and cooling solutions, meeting the diverse needs of today's consumers.