Heat Controller HMH30AS-1, HMC30BS-1, HMC30AS-1 manual Connect the cable to the Indoor unit, AWG #20

Page 13

CONNECTING THE CABLE BETWEEN INDOOR UNIT AND OUTDOOR UNIT

Connect the cable to the Indoor unit.

Connect the cable to the indoor unit by connecting the wires to the terminals on the control board individually according to the outdoor unit connection.

(Ensure that the color of the wires of the outdoor unit and the terminal No. are the same as those of the indoor unit.)

Terminals on the indoor unit

 

 

 

 

3(L1)

4(L2)

 

5

 

Color of Wires

 

 

 

 

 

 

 

 

 

 

 

 

 

 

G/Y

BROWN

 

BLUE

RED

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Color of Wires

 

G/Y

BROWN

 

BLUE

RED

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Terminals on the outdoor unit

1(L1)

2(L2)

 

 

 

 

3(L1)

4(L2)

 

5

 

CAUTION

The power supply cord connected to the outdoor unit should be complied with the following specifications (UL and CSA recognized one).

 

 

G

AWG #12

 

 

 

Ø8.5mm

(0.33in)

N/YL

 

20m

m

 

 

 

 

(0.

 

 

79in)

The connecting cable connected to the indoor and outdoor unit should be complied with the following specifications (UL and CSA recognized one).

POWER INPUT

Ø 7.5mm

(0.30in)

AWG #20

GN/YL

20m

m

(0.

79in)

CAUTION

Wiring must be as following diagram.

Disconnect Switch (Optional)

May be required by local codes

Must be rated for 15 amps

Indoor

unit

61cm max (24 in max)

Main power source

Outdoor Disconnect Switch

• Must be rated for 30 amps

Outdoor

unit

61cm max (24 in max)

13

Image 13
Contents HMC30AS-1/HMH30AS-1, HMC30BS-1/HMH30BS-1Single-Zone Refer to Installation OverviewFor right rear piping Two type B screwsDo not install it yourself customer Following should be Always Observed for SafetyRooftop Installations Installation of INDOOR, Outdoor UnitSelect the best location Piping length and elevationInstallation Plate Type a screw How to mount installation plateDrill a hole in the wall IndoorFlaring work Flaring Work and Connection of PipingConnection of piping -Indoor Remove the front right side panel by the arrow Indoor unit installationRemove the lower panel by the arrow Wrap the insulation material around the connecting portion Suction Evaporator Connecting cable84.2kg.m Tighten the flare nut with a wrenchSection Reinstall the parts to the original positionFor left piping. Follow the instruction below Installation Information For left piping Good caseBad case Connection of piping -Outdoor Connection of the drain hoseFollows the arrow on the wrench 30kConnect the cable to the Indoor unit Wiring must be as following diagramAWG #20 Outdoor Unit Connect the cable to the outdoor unitRemove the right side panel Checking the drainageRemove the lower panel by the arrow To check the drainage Drain pipingSeal small openings around pipings with a gum type sealer Form the pipingAir purging AIR PurgingAir purging with vacuum pump PreparationEvacuation Soap water methodFinishing the job Charging Pump Down Procedure Prepare remote controlTest Running Settlement of outdoor unitMemo Memo No A20001V

HMC30AS-1, HMH30BS-1SINGLE-ZONE, HMH30AS-1, HMC30BS-1 specifications

The Heat Controller HMC30AS-1, HMH30AS-1, HMH30BS-1 SINGLE-ZONE, and HMC30BS-1 are cutting-edge HVAC systems designed to provide optimal comfort and efficiency in both residential and commercial settings. These models embody the latest advancements in heating and cooling technology, making them ideal choices for anyone looking to enhance their indoor environment.

One of the standout features of these heat controllers is their energy efficiency. With advanced inverter technology, these products adjust compressor speed based on the heating or cooling demand, significantly reducing energy consumption compared to traditional systems. This not only lowers utility bills but also reduces environmental impact, making them a sustainable choice for eco-conscious consumers.

The HMC30AS-1, HMH30AS-1, HMH30BS-1 SINGLE-ZONE, and HMC30BS-1 also come with programmable thermostats, allowing users to set specific temperature schedules according to their daily routines. This convenience ensures that spaces are always at the desired temperature when occupied, providing a perfect balance between comfort and energy conservation.

Another impressive characteristic is their quiet operation. These systems are engineered with sound-dampening technology, minimizing noise levels and ensuring a peaceful indoor atmosphere. This is especially beneficial for bedrooms, offices, or any spaces where tranquility is essential.

Durability and reliability are also hallmarks of these models. Built with high-quality materials and robust components, they are designed to withstand varying environmental conditions while providing consistent performance. The heat controllers also come with comprehensive warranties, giving users added peace of mind regarding their investment.

In addition to their efficiency and durability, these systems offer versatile installation options. Whether it's a compact single-zone setup or a larger installation, the HMC30 series is adaptable, making it suitable for various building layouts.

With their modern design and user-friendly interfaces, these heat controllers blend seamlessly into contemporary spaces. Smart technology options enable integration with mobile apps and smart home systems, allowing for remote monitoring and adjustment.

From energy-saving features to quiet operation, the Heat Controller HMC30AS-1, HMH30AS-1, HMH30BS-1 SINGLE-ZONE, and HMC30BS-1 represent the pinnacle of heating and cooling solutions, meeting the diverse needs of today's consumers.