Heat Controller 7602-443 user manual Temperature Adjustment, Fan Mode Selection

Page 4

User Manual

7602-443 COMMUNICATING, PROGRAMMABLE THERMOSTAT

Heat Controller, Inc.

 

 

 

2.0 Temperature Adjustment

To adjust the temperature on the thermostat, use the left/ right arrow buttons to select the TEMP user option on the Home Screen and then press the center button or press the up or down arrow key. The Temperature Adjustment Display appears and shows either one (in Heat, Cool, or Emergency Heat modes) or both (in Auto mode) temperature setpoints. Adjust the setpoints using the up/down arrow buttons. Navigate between setpoints using the left/right arrow buttons. Press the center button to save changes.

Heat Setpoint (default 60°F): options: 55°F to Maximum Heating Setpoint Limit (section 5.6.8)

Cool Setpoint (default 80°F): options: Minimum Cooling Setpoint Limit (section 5.6.8) to 95°F

NOTE 1: The thermostat must be in any mode other than OFF (section 2) to adjust temperature setpoint(s).

NOTE 2: The thermostat forces a 2°F “dead-band” between the Heating and Cooling setpoints. While adjusting the Heating setpoint, the Cooling setpoint may be automatically increased to enforce a 2°F “dead- band”. Likewise, while adjusting the Cooling setpoint, the Heating setpoint may be automatically reduced to enforce a 2°F “dead-band”.

NOTE 3: In programmable mode, the TEMP option provides the ability to temporarily modify setpoint(s) until the start time of the next program schedule event. While in non-programmable mode, the TEMP option provides the ability to modify the setpoint(s).

3.0 Fan Mode Selection

To adjust the Fan Mode on your thermostat, use the left/ right arrow buttons to select the FAN user option from the Home Screen and then press the center button. The Fan Menu shows up to 3 possible Fan Operating Modes with the currently active Fan Operating Mode highlighted. Use the up/down arrow buttons to select the desired Fan Mode and press the center button to save your selection. You may choose from the following Fan Modes:

Auto (default): Fan only runs with a call for heating/cooling

Continuous On: Fan runs continuously with or without a call for heating/cooling

Programmed Fan (in Programmable Mode): Fan runs per Program Schedule settings (reference section 5.3).

10/13/11

8:25 AM

 

FAN AUTO

RH 41%

HUMID ON

68°

AUTO

SETPOINT

HEAT 62

COOL 82

RH TEMP MODE FAN MENU

HOLD THIS

TEMPERATURE

UNTIL 5:00 PM

HEAT COOL

70° 74°

CHANGE SET TEMP PREVIOUS SAVE

10/13/11

8:27 AM

 

FAN AUTO

RH 40%

 

69°

OFF

RH TEMP MODE FAN MENU

FAN MENU

AUTO

CONTINUOUS ON

PROGRAMMED FAN

HEAT

SELECT OPTION

PREVIOUS SAVE

4

Image 4
Contents Communicating, Programmable Thermostat Table of Contents Operating Mode Selection Menu Navigation ShortcutsFan Mode Selection Temperature AdjustmentChange SET Temp Previous Save Humidity Level Adjustment Setpoint Heat Cool RH Temp Mode FAN Menu Humidity ControlSettings Main Menu Options OverviewRH Temp Mode FAN Menu Main Menu Main MenuMain Menu SET Date and Time Hold MenuHold this Temperature Until 500 PM PermanentProgram Menu Copy Heat Cool FANAuto Leave AutoOther Settings Screen Settings Program SettingsSmart Recovery OffsetsProgrammed Demand Reduction Mode Demand Reduction Option for Program OperationProgrammed Demand Reduction Operation For Climadry Programmed Demand Reduction FAN OperationFault Staus Active Fault Fault Code E2 High Refrig PressureProgrammed Demand Reduction Schedule Start END Time MON TUETemperature Status Security Lockout Main Menu SET Date and Time Hold Program FAN Mode SettingsTotal Keypad Lockout Select Option Previous Save Service Needed Night Setback FAN OperationRevision History