Heat Controller HTS SERIES manual General Information

Page 5

T h e Q u a l i t y L e a d e r i n C o n d i t i o n i n g A i r

Inspection

Upon receipt of the equipment, carefully check the shipment against the bill of lading. Make sure all units have been received. Inspect the packaging of each unit, and inspect each unit for damage. Insure that the carrier makes proper notation of any shortages or damage on all copies of the freight bill and completes a common carrier inspection report. Concealed damage not discovered during unloading must be reported to the carrier within 15 days of receipt of shipment. If not filed within 15 days, the freight company can deny the claim without recourse. Note: It is the responsibility of the purchaser to file all necessary claims with the carrier. Notify your equipment supplier of all damage within fifteen (15) days of shipment.

Storage

Equipment should be stored in its original packaging in a clean, dry area. Store units in an upright position at all times. Stack units a maximum of 3 units high.

Unit Protection

Cover units on the job site with either the original packaging or an equivalent protective covering. Cap the open ends of pipes stored on the job site. In areas where painting, plastering, and/or spraying has not been completed, all due precautions must be taken to avoid physical damage to the units and contamination by foreign material. Physical damage and contamination may prevent proper start-up and may result in costly equipment clean-up.

Examine all pipes, fittings, and valves before installing any of the system components. Remove any dirt or debris found in or on these components.

Pre-Installation

Installation, Operation, and Maintenance instructions are provided with each unit. Horizontal equipment is designed for installation above false ceiling or in a ceiling plenum. Other unit configurations are typically installed in a mechanical room. The installation site chosen should include adequate service clearance around the unit. Before unit start-up, read all manuals and become familiar with the unit and its operation. Thoroughly check the system before operation.

Prepare units for installation as follows:

1.Compare the electrical data on the unit nameplate with ordering and shipping information to verify that the correct unit has been shipped.

2.Keep the cabinet covered with the original packaging until installation is complete and all plastering, painting, etc. is finished.

3.Verify refrigerant tubing is free of kinks or dents and that it does not touch other unit components.

R e s i d e n t i a l S p l i t - 6 0 H z R 4 1 0 A

R e v. : 0 3 A u g u s t , 2 0 1 2

General Information

4.Inspect all electrical connections. Connections must be clean and tight at the terminals.

5.Loosen compressor bolts on units equipped with compressor spring vibration isolation until the compressor rides freely on the springs. Remove shipping restraints.

6.Locate and verify any hot water generator (HWG) or other accessory kit located in the compressor section.

CAUTION!

WARNING! All refrigerant discharged from this unit must be recovered WITHOUT EXCEPTION. Technicians must follow industry accepted guidelines and all local, state, and federal statutes for the recovery and disposal of refrigerants. If a compressor is removed from this unit, refrigerant circuit oil will remain in the compressor. To avoid leakage of compressor oil, refrigerant lines of the compressor must be sealed after it is removed.

CAUTION!

CAUTION! To avoid equipment damage, DO NOT use these units as a source of heating or cooling during the construction process. The mechanical components and filters will quickly become clogged with construction dirt and debris, which may cause system damage.

www.heatcontroller.com

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents GeoLogix HTS Series Split System Two Stage, 2-5 Tons Table of Contents Model Nomenclature for Indoor Split Series Safety SafetyGeneral Information General Equipment SelectionIndoor Coil Selection HTS GeoLogix WDG/MWG Indoor Section Matches for Ahri RatingsSelecting Air Handler Air Handler Selection ExampleRemoving Existing Condensing Unit Where Applicable InstallationAir Handler and Coil Installation Indoor Compressor Section LocationPiping Installation HTS InstallationAntifreeze Ground-Loop Heat Pump ApplicationsFlushing the Earth Loop Antifreeze Percentages by Volume Approximate Fluid Volume U.S. gal. L per 100’ of Pipe100% USP food grade Propylene Glycol EthanolMotorized Modulating Water Control Valve Water Quality StandardsExpansion Tank and Pump 026-049 Sizes 064 Ground-Water Heat Pump ApplicationsClosed OpenWater Quality Standards Water Quality StandardsLine Set Installation Refrigeration InstallationEvacuation and Charging the Unit Installing the Indoor Coil and LinesetAdd-On Heat Pump Applications WDG Total Charge Method Evacuation Of The Lineset And CoilCharging The System Determining Sub-Cooling Checking Superheat and Subcooling Determining SuperheatHot Water Generator Typical HWG Installation Indoor Compressor SectionWater Tank Preparation InstallationWater Tank Refill HWG Water PipingInitial Start-Up HWG Water Piping Sizes and LengthGeoMax 2 HTS Electrical Data Electrical Line VoltageAccessory Connections Low Water Temperature Cutout SelectionElectrical Low Voltage Terminal StripThermostat Connections Electrical Thermostat WiringThermostat Installation Unit Operation DXM2 ControlsDXM2 Layout and Connections Indoor Split HTS024-060 Wiring Diagram 208-230-/60/1 DXM2 Operating Limits Unit Commissioning And Operating ConditionsBuilding Operating Limits Commissioning ConditionsUnit and System Checkout Unit Start-up ProcedureUnit Start-Up and Operating Conditions Manual Operation Unit Start-Up ProcedureGPM Unit Operating ConditionsTon Preventive Maintenance Sensor Nominal resistance at various temperatures Basic Troubleshooting InformationSystem Configuration Advanced Troubleshooting and Configuration InformationService Mode Start DXM2 Process Flow ChartFault Htg Clg Possible Cause Solution Functional TroubleshootingIFC Fault Code Symptom Htg Clg Possible Cause Solution Performance Troubleshooting\SH Troubleshooting FormS i d e n t i a l S p l i t 6 0 H z R 4 1 0 a Wellworth Ave., Jackson, Michigan 49203 Ph -0787-2100 Fax

HTS SERIES specifications

The Heat Controller HTS Series is a cutting-edge solution for climate control, designed to offer superior performance and unmatched comfort. This advanced heating and cooling system stands out in today's market due to its innovative technologies and user-friendly features.

One of the main features of the HTS Series is its energy efficiency. Equipped with the latest inverter technology, it adjusts the compressor speed to maintain the desired temperature while consuming less energy. This not only reduces operational costs but also minimizes the carbon footprint, making it an environmentally friendly choice.

Another standout characteristic of the HTS Series is its precise temperature control. The system utilizes advanced sensors to monitor indoor conditions in real-time, ensuring that you experience consistent comfort throughout your space. The ability to quickly react to changes in temperature helps maintain an optimal environment, regardless of external weather fluctuations.

The HTS Series also boasts a robust air filtration system. With multiple filter layers, including HEPA filters, it effectively captures dust, allergens, and other airborne pollutants. This feature makes the HTS Series an excellent choice for families with allergies or respiratory concerns, promoting a healthier indoor atmosphere.

Furthermore, the heat pump technology incorporated in the HTS Series allows for both heating and cooling capabilities. In cooler months, it efficiently extracts heat from the outside air to warm your living spaces, while during the summer, it reverses the process to provide refreshing cool air. This dual functionality enhances versatility, making it suitable for various climates.

User convenience is paramount in the HTS Series design. It comes with a smart thermostat that enables remote operation via a mobile app, providing users with flexible control over their environment. Additionally, the intuitive interface and programmable settings allow for seamless customization, adapting to your daily schedule and preferences.

Durability and quiet operation are also key attributes of the HTS Series. Built with high-quality materials and components, it ensures long-lasting performance, while its sound-dampening technologies provide whisper-quiet operation, enhancing the comfort of your home or office space.

In summary, the Heat Controller HTS Series represents the pinnacle of home heating and cooling technology. With its energy efficiency, precise temperature control, superior air filtration, dual functionality, and user-friendly features, it stands as a leading choice for those seeking reliable and effective climate solutions. This series not only enhances comfort but also supports a sustainable lifestyle for the future.
Top Page Image Contents