Heat Controller BDE-123-A Disassembly Instructions, Mechanical Parts, Front Grille, Cabinet

Page 6

2. DISASSEMBLY INSTRUCTIONS

— Before the following disassembly, POWER SWITCH is set to OFF and disconnected the power cord.

2.1 MECHANICAL PARTS

2.1.1 FRONT GRILLE

1. Open the inlet grille upward or downward.

2. Remove the screw which fastens the front grille.

3. Pull the front grille from the right side.

4. Remove the front grille. (See Fig. 1)

5. Re-install the component by referring to the removal procedure.

Figure 1

2.1.2 CABINET

1.After disassembling the FRONT GRILLE, remove the 9 screws which fasten the cabinet at the both sides and the top. (See Fig. 2)

Keep these for later use.

2.1.3 CONTROL BOX

1.Remove the front grille. (Refer to section 2.1.1)

2.Remove the screw which fasten the control box. (See Fig. 3)

3.Pull the control box from the barrier.(See Fig.3)

4.Discharge the capacitor by placing a 20,000 ohm resistor across the capacitor terminals.

5.Disconnect two wire housings in the control box.

6.Pull the control box forward completely.

7.Re-install the components by referring to the removal procedure. (See Fig. 3)

(Refer to the circuit diagram found on pages 26~27 in this manual and on the control box.)

Figure 2

Figure 3

— 6—

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Models BDE-103-A BDE-123-AContents PrefaceSpecifications For BDE-103-A/BDE-123-ACooling only Model Operation FeaturesControl Locations VentilationCooling and Heating Model Operation Heat Pump ModelsFront Grille Disassembly InstructionsMechanical Parts CabinetAIR Handling Parts ORIFICE, Heater Assy and Turbo FAN2 FAN Motor Electrical PartsShroud CompressorPower Cord Rotary SwitchThermostat Evaporator Refrigeration CycleCondenser Capillary TubePage Pulling Vacuum Dimension of sleeve assembly optional HOW to Install the UnitDimension of air conditioner If YOU Want to Pull OUT the Filter DownwardInstallation Kits Contents Suggested Tool Requirements Sleeve up to 18 inches deepUnit Installation Troubleshooting Guide Outside DimensionsPiping System Troubleshooting Guide Fails to Start Complaint Cause Remedy Room AIR Conditioner Voltage Limits Complaint Cause Remedy Schematic Diagram Circuit DiagramExploded View Model BDE-103-A/BDE-123-AReplacement Parts List Model BDE-103-A/BDE-123-AHeat CONTROLLER, INC

BDE-103-A, BDE-123-A specifications

The Heat Controller BDE-123-A and BDE-103-A are advanced heating units designed to enhance comfort in residential and commercial spaces. With an emphasis on energy efficiency, these models incorporate a range of technologies and features that structure their performance and usability.

Both units utilize innovative inverter technology, allowing for precise control over temperature settings. This feature not only reduces energy consumption but also minimizes fluctuations in room temperature, ensuring consistent comfort levels. The inverter technology enables the units to adjust their power output based on the current demand, which leads to reduced operational costs and a longer lifespan for the units.

One of the standout characteristics of the BDE-123-A and BDE-103-A models is their robust heating capabilities. The BDE-123-A, with a greater heating capacity than the BDE-103-A, serves larger spaces efficiently, making it ideal for larger rooms or open areas. The BDE-103-A, while slightly less powerful, is well-suited for smaller rooms or specific zones in a house, providing an effective heating solution without excessive energy use.

Both models are equipped with user-friendly digital control panels, enabling easy adjustments to settings and temperatures. The intuitive interface allows users to select their desired heating preferences with ease, enhancing the overall user experience. Additionally, these heat controllers come with programmable timers, allowing users to set heating schedules that align with their daily routines, optimizing energy use even further.

In terms of installation, both the BDE-123-A and BDE-103-A boast versatile mounting options, which can accommodate various configurations. Their sleek designs ensure they blend seamlessly into different décor styles, making them visually appealing additions to any space. Furthermore, these models are designed with low noise levels, providing a quiet operation that doesn’t disrupt the tranquility of your environment.

Safety features are also prioritized in these units. They include overheat protection and an automatic shut-off function, ensuring safe operation even in demanding conditions. Overall, the Heat Controller BDE-123-A and BDE-103-A represent a blend of advanced technology, effective heating performance, and user-friendly features, making them exemplary choices for efficient heating solutions in contemporary settings.
Top Page Image Contents