Sony MDS-S37 operating instructions Beep Output During Operations, Operation Beep sound

Page 31

Beep Output During

Operations

Your deck can output various beeps to allow you to verify deck operations by sound.

The beeps are output from both the deck itself and the headphones.

Rear of the deck

 

LINE

DIGITAL

BEEP

(ANALOG)

 

 

IN

OUT

 

 

 

IN

OUT

 

 

L

 

ON OFF

 

R

 

 

BEEP

Switch BEEP to ON.

A high- or low-pitched beep is output to indicate the following operations.

Additional Information

Operation

Beep sound

 

 

The deck has been turned on.

One short beep (high)

 

 

The deck has been turned off.

Two short beeps (high)

 

 

An operation button was pressed

Three short beeps

with no MD loaded.

(high), followed by one

 

continuous beep (high)

rwas pressed but the MD is full. One continuous beep (high)

r was pressed and the deck has

Consecutive beeps (low)

changed to recording pause.

are emitted, one for each

 

 

10 minutes of remaining

 

 

time on the MD*,

 

 

followed by single beeps

 

 

every few seconds.

 

 

 

 

 

ß (áor P) was pressed and

One short beep (high)

 

the deck has started recording.

 

 

 

 

 

 

 

The deck is recording or in

One continuous beep

 

recording pause and the peak

(low)

 

level meter level has exceeded the

 

 

 

recommended level**

 

 

 

(“OVER” lights up).

 

 

 

 

 

 

 

The deck is recording and the

Several short beeps

 

remaining time on the MD has

(high)

 

dropped below 3 minutes**.

 

 

 

 

 

ß(áor P) was pressed and

One short beep (high)

the deck has started playing.

 

 

 

 

 

 

p was pressed.

One short beep (low)

 

 

 

 

PLAY MODE was pressed while

One short beep (low)

 

the deck is stopped, and

 

 

 

continuous (normal) play mode

 

 

 

has been selected (canceling

 

 

 

Shuffle or Program Play mode).

 

 

 

 

 

EDIT/NO was pressed while the

One short beep (high)

deck is stopped, and “All Erase ?”

 

 

has appeared in the display.

 

 

 

 

 

EDIT/NO was pressed while the

One short beep (high)

deck is recording, and

 

 

“LevelSync ?” has appeared in the

 

 

display **.

 

 

 

 

 

 

 

EDIT/NO was pressed while the

One short beep (high)

 

deck is playing, and “Erase ?” has

 

 

 

appeared in the display.

 

 

 

 

 

 

*One beep for each 10 minutes of remaining time (e.g., one beep for 10 to 20 minutes, two beeps for 20 to 30 minutes, and three beeps for 30 to 40 minutes). No beep is output for a remaining time of 10 minutes or less.

**This beep is output only through the headphones; no beep is output from the deck.

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents MiniDisc Deck Precautions About This Manual WelcomeOverview UnpackingHooking Up the System Inserting batteries into the remoteConnecting the deck to an amplifier Connecting the AC power cordHookups To record through Set Input to To record Set REC Mode toPress When TOC flashes in the displayDo the following Playing an MDChecking the remaining recordable time on the MD Useful Tips for RecordingPlaying back tracks just recorded Monitoring the input signal Input MonitorIf Auto Cut appears in the display Auto Cut If Smart Space appears in the display Smart SpaceTo record from the middle of the track Adjusting the Recording LevelRecording Over Existing Tracks While Track flashes in the displayMarking Track Numbers While Recording Track Marking To cancel Automatic Track MarkingTo stop Music Synchro-Recording To stop Time Machine RecordingYou can change CDs during synchro-recording Synchro-Recording With a Sony CD PlayerIf the CD player does not start playing To pause recordingChecking remaining time and the title of a track Using the DisplayLocating a Specific Track Playing Tracks Repeatedly Locating a Particular Point in a TrackRepeating the current track Repeating a specific portion A-B Repeat Playing in Random Order Shuffle PlayChecking the track order Creating Your Own Program Program PlayChanging the track order Erasing Recordings Erase Function Pausing after each track Auto PauseInserting blank spaces while recording to tape Auto Space Erasing a part of a track To cancel the Erase FunctionErasing a single track Erasing all tracks on an MDYou can undo a track division To cancel the Divide FunctionYou can divide a track while recording You can undo a track combination To cancel the Combine FunctionLabeling Recordings Title Function To cancel the Move FunctionTo label Make sure that the deck is If you entered the wrong character To cancel labelingTo select UntilTo select Press Labeling tracks and MDs with the remoteChanging an existing title Z Undoing the Last Edit Undo FunctionErasing all titles on a disc Name Erase Function Some tracks cannot be combined with others Display MessagesSystem Limitations Message MeaningTroubleshooting Outputs SpecificationsOptional accessories InputsOperation Beep sound Beep Output During OperationsGuide to the Serial Copy Management System Turntable Tuner W, X, Y, Z IndexNames of controls Additional InformationIndex
Top Page Image Contents