JVC UX-J50, UXJ60 manual Important for Laser Products

Page 2

Warnings, Cautions and Others

IMPORTANT for the U.K.

DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.

BE SURE to replace the fuse only with an identical approved type, as originally fitted.

If nonetheless the mains plug is cut off ensure to remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.

If this product is not supplied fitted with a mains plug then follow the instructions given below:

IMPORTANT:

DO NOT make any connection to the terminal which is marked with the letter E or by the safety earth symbol or coloured green or green-and-yellow.

The wires in the mains lead on this product are coloured in accordance with the following code:

Blue : Neutral

Brown : Live

As these colours may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

IF IN DOUBT—CONSULT A COMPETENT ELECTRICIAN.

IMPORTANT FOR LASER PRODUCTS

REPRODUCTION OF LABELS

1CLASSIFICATION LABEL ON EXTERIOR SURFACE

2WARNING LABEL INSIDE THE UNIT

 

CAUTION: Invisible

laser

 

ADVARSEL: Usynlig laser-

 

VARNING:

Osynlig

laser-

 

VARO: Avattaessa ja suo-

 

 

radiation when open

and

 

stråling ved åbning, når

 

strålning när

denna

del

är

 

jalukitus

ohitettaessa

olet

 

 

interlock failed or defeated.

 

sikkerhedsafbrydere

er ude

 

öppnad och spärren är

 

alttiina

näkymättömälle

 

 

AVOID DIRECT EXPOSURE

 

af funktion. Undgå udsæt-

 

urkopplad.

Betrakta

ej

 

lasersäteilylle. Älä

katso

 

 

TO BEAM.

(e)

 

telse for stråling

(d)

 

strålen.

 

 

(s)

 

säteeseen.

(f)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.CLASS 1 LASER PRODUCT

2.CAUTION: Invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam.

3.CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1.Do not remove screws, covers or cabinet.

2.Do not expose this appliance to rain or moisture.

CAUTION—STANDBY/ON button!

Disconnect the mains plug to shut the power off completely (the

STANDBY/ON lamp goes off). The STANDBY/ON button in any position does not disconnect the mains line.

When the unit is on standby, the STANDBY/ON lamp lights red.

When the unit is turned on, the STANDBY/ON lamp lights green.

The power can be remote controlled.

CAUTION

Do not block the ventilation openings or holes.

(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)

Do not place any naked flame sources, such as lighted candles, on the apparatus.

When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly.

Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

CAUTION: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:

1 Front:

No obstructions and open spacing.

2 Sides/ Top/ Back:

No obstructions should be placed in the areas shown by the dimensions below.

3 Bottom:

Place on a level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm or more.

Front View

15 cm

 

Side View

15 cm

 

 

 

1 cm

1 cm

 

 

 

15 cm

 

15 cm

15 cm

 

 

 

 

 

UX-J60

 

 

 

 

UX-J50

 

 

10 cm

 

 

UX-J60/UX-J50

G-1

Image 2
Contents Instructions Important for Laser Products Above ALL About This Manual PrecautionsIntroduction Contents Front Panel Location of the Buttons and ControlFront Panel For UX-J50Display Window Pressing this button also turns on the unitRemote Control 10+10Getting Started Supplied AccessoriesConnecting Antennas FM antenna To connect an outdoor FM antennaTo connect an outdoor AM MW antenna Connecting SpeakersAM MW antenna For UX-J60To remove the speaker grilles Connecting Other EquipmentRelease your finger from the clamp To connect an audio equipmentPress CLOCK/TIMER Setting the ClockTurning On the Power Press UP or Down to Adjust the hour, thenBass level or press Treble to adjust the treble level Adjusting the VolumePress Bass to adjust Enjoying Sound EffectsTo enjoy the heavy sound only for UX-J60 Selecting the Display Color only for UX-J60Selecting the Illumination Brightness Press Sound TurboTuning in to a Station Presetting StationsReceiving FM Stations with RDS Tuning in to a Preset StationPress UP or Down to select a preset number Press Display orange-colored Changing the RDS InformationSearching for Programs by PTY Codes PTY Search Press PTY SearchData type you want appears on Display Switching Temporarily to a Program Type of Your ChoicePress TA/NEWS/INFO until Wait for about 3 seconds after specifying the data typePress CD Playing Back DiscsPlaying Back the Entire Disc-Normal Play Press CD 3/8Basic Disc Operations Program PlayProhibiting Disc Ejection-Tray Lock Playing at Random-Random PlayRepeating Tracks-Repeat Play Press RandomPlaying Back Tapes To play both sides-Reverse ModePress REV.MODE reverse mode Playing Back a TapeRecording on a Tape To record on both sides-Reverse ModeRecording Press REC recordingTo stop while recording, press Press REV.MODE reverse mode repeatedly Until or is litDisc Direct Recording Set the on-time when you want the unit to turn on Using the TimersUsing Daily Timer and Recording Timer Set the off-time when you want the unit to turn off standbyPress STANDBY/ON to turn Using Sleep TimerAdjust the clock if you need Press SleepMaintenance TroubleshootingDescription of the PTY codes Alarm functionAdditional Information Test functionSpecifications Memo Memo 0103MWMMDWJEM