JVC GV-DS1, LYT0002-0M1B, 0397MKV*UN*YP manual Automatically, Select Interval Capture

Page 28

28VIDEOCAPTURE (cont.)

INTERVAL CAPTURE

The Interval Capture mode is best suited for capturing images at set intervals from a video source unit with a JLIP connector.

Set-up

 

Capture Mode

Step by Step

Image Format

Automatic

Device Change

 

Initialize

 

ID Change

 

Counter Reset

 

 

 

VCR

 

I

00:01:23:12F

Capture

Transfer

NOTE:

•Make sure that enough hard disk space is available on your computer before executing video transfer.

For full image data space requirements,

☞ p. 24.

•Transfer of the index image and full image starts at the image box bordered in green.

Click and select the desired image box. •When transferring full image data using the Bitmap image format (9.bmp), the transfer takes a very long time, causing the video source unit to stop playback

automatically.

Preparation

•Make sure all units are properly connected (☞ p. 12).

•Insert a tape into the video source unit.

In the "Set-up" menu, click "Image Format". Select "Field Picture" in the Capture Mode. (☞ p. 29).

1 At the menu bar, click "Set-up" — "Capture Mode" — "Automatic".

•The "Automatic Transfer" window appears.

2 Select the data to be transferred.

•When you select "Index Image", only the index image (80 x 60 pixels) is transferred to your computer.

•When you select "Index & Full Image", both index image (80 x 60 pixels) and full image (640 x 480 pixels) are transferred to the computer.

3 Select "Interval Capture".

4 Set the interval.

•Select the time interval at which images are captured.

5 Set the number of images to be captured and click "OK".

•From 1 up to 99

6 Click "Window" — "VCR" to call up the VCR Operation Window. Start video playback a few seconds prior to the point where you want image capturing to start.

7 Operate the video source unit via the VCR Operation window and click the "Transfer" button at the desired image to start the capture function.

1.The message "No. 1 index image being transferred" appears while the index image is being transferred to the computer.

2.When you select "Index & Full Image" in step 2, the message "No. 1 full image being transferred" appears while the full image is being transferred to the computer.

3.The message "Index No. 2 being scanned" appears while the video tape is fast-for- warded and played at the time intervals set in step 4 to scan the video data on the VCR.

•The image selected when "Transfer" is clicked is captured and subsequent images are captured at the time interval specified by the counter value selected in step 4.

•The video source unit enters the Pause mode when capture is complete.

Page 27 Page 29
Image 28
Page 27 Page 29
Contents GV-DS1 Dear Customer Declaration of ConformityPower Sources Power Cord ProtectionPower Lines Grounding or PolarizationAccessories Damage Requiring ServiceCleaning Replacement PartsDo not place the Video Capture Docking Station How to handle a CD-ROM MaintenanceJlip Video Capture Software Video Capture FacilityJlip Control Facility Data Sharing With Jlip Player Soft- wareHOW to Open the Program HOW to Close the Program HOW the Desktop WorksPicture Format Setting IntroductionTroubleshooting Major Specifications Index Jlip Player SoftwareGetting Started Video Printer Operation GV-PT2Advanc ED AP P Licat Ions Create title indexes for your video collectionBusiness presentations Internet homepageMulti connector Jlip jack p Capture input EXT./printer connectorPlay button Pause buttonImage sources with Jlip and video output connectors Connector Video Capture Docking StationCore filter EXTWhat is video capture software ? What is Jlip ?Operating Environment Connectable DevicesInstallation Procedure WindowsHO W to Open the PRO Gram PreparationInitializing Jlip Select Transfer Rate. Normally selectItiali ZA Tion Select UnitsHOW to Close the Program Menu bar Main Desktop WindowControl buttons Menu BAR Image display areaEach pulldown menu is configured as follows ExitVCR operation window Image data flow Capturing Video ImagesFull image data is transferred to the computer Step by Step CaptureRepeat steps 2 through 5 as required Ideo CA Pture Automatic CaptureProgram Capture Make sure all units are properly connected pTransfer Automatically Interval CaptureSelect Interval Capture Picture Data Format Capture ModeSelecting a Picture Format Counter Reset Counter Value ChangeModify Capture Point window appears TransferredChange ID Delete Index Image and Full ImageYou can change the Video Capture Unit’s ID number Create NEW Folder SavingOpen the menu bar and click File New Album Saved, you will be asked whether to save or notOpen Index Save the Full Image DataUsing Jlip Player Software Data Open JLIPjlp File window is displayedHOW to Store Jlip Player Data Save As Jlip jlp File window is displayedProblem Cause Counter cannot be reset Where the program run fileCannot capture video data With the desired counterMessage Appears when Action Error Execute afterPlaying back Not enough diskMemo Jlip Player Software Section Connections When Using Jlip Playe r Soft ware When connected with the Video PrinterDigital camcorder JlipGettin G Started Devices to connect to the Video Capture BOXInstalling Jlip Player Software Prepare Devices Starting Jlip Player SoftwareSelect Serial Port Select Devices Drop Frame System Title barMemo Elapsed TimeBasic Oper AT Ions Setting in/out pointsOperating camcorder Select Scene Start PlaybackTo confirm all programmed scenes, click Start Only the camcorder movesBasic OP Eration S DubbingPrepare NEW Tape Start EditingStart Saving Enter File NameSave File Select Floppy Disk DriveOpening a saved file BA SIC OP E RationsCorrecting and cutting the programmed counter data Overwriting the file Designateied Scene to be COPStore Designated Scene in Memory Designate Scene to be TransferredPosition button Power button Icon buttonStore button Scene selectPrint Printing Bring UP Video Printer WindowPlayback Store SceneAdjusting picture equalization Access Picture Equalization Dialog BOXQuitting the Movie Player window Click Close Choose Exit from FileAuto Capture PreparationTo Print Captured Video Data with Video Printer Load the tape into the video unitTo print only the cut-in scene on the edited tape Click Print to start printingAdvan CED Oper AT Ions Connecting other device during operationChanging ID number Access Name Change Dialog BOX Access Device Selection Dialog BOXWhen Using the Video Capture Software Enter NEW Name SET NEW NameAccess Pause Time CORREC- Tion Dialog BOX Advanc ED Operat IonsEnter Value Determine ValueError - This application will That power is onPower on all devices System Communication error Check devices - ConfirmAjor Speci Ficat Ions Setup Menu Automatic Capture Auto BitmapChange ID COM Port Delete Index Image and Full Image Desktop Window Pg , 48GV-DS1
Top Page Image Contents