JVC 0397MKV*UN*YP manual Error - This application will, Check devices - Confirm, That power is on

Page 65

TROUBLESHOOTING 65

MESSAGE

⬤ POSSIBLE CAUSE

⬛ CORRECTIVE ACTION

 

 

 

Error – – This application will

⬤ The COM port used for the JLIP connector is not

close.

selected, or the COM port is selected but the

Check devices – – Confirm

connection is wrong.

that power is ON.

⬛ Check the connected COM port and select it on the

 

"Serial Port Selection" screen (☞ pg. 46).

 

 

No devices detected to

⬤ Power is not supplied or the connection is wrong.

connect.

⬛ Connect the devices correctly and turn them on

Power ON all devices in

(☞ pg. 42, 43).

system.

 

 

 

Communication error

⬤ Device is not turned on or cable is disconnected.

(&H (number))

⬛ Connect the device correctly and turn it on

Check cable connection.

(☞ pg. 42, 43).

 

⬛ If device was turned off and on again during

 

operation, click "OK". All devices should function

 

properly.

 

 

Select the device to control.

⬤ The line where the name of the device to use

 

appears is not clicked.

 

⬛ Click on it and "OK" (☞ pg. 47).

 

 

No video cassette!!

⬤ The video cassette is not loaded in the camcorder.

Load a video cassette to ID

When the video cassette is removed during

(number).

operation, this message appears.

 

⬛ Insert the video cassette into the camcorder.

 

 

Invalid entry in scene

⬤ The value of the CUT OUT point is smaller than

(number) (There is IN > OUT

the CUT IN point's.

condition). Correct the time

⬛ Set the value of the CUT OUT point so that it is

or delete the scene.

larger than the CUT IN point's (☞ pgs. 50, 54).

 

 

Select a number between 0

⬤ When correcting the CUT IN/OUT points, the

and 29.

value you set differs from the original by over 30

 

frames.

 

⬛ Select integral number from 0 to 29 (☞ pg. 54).

 

 

Invalid frame number on drop

⬤ Because the DV-format digital camcorder uses the

frame counter.

drop frame system, inputting frame 00 and 01 is

 

impossible.

 

⬛ Input frame value other than 00 or 01

 

(☞ pgs. 48, 54).

 

 

The monitor displays of the application software illustrated in this manual may differ from those you are actually viewing depending on the operating environment of your computer.

Page 64 Page 66
Image 65
Page 64 Page 66
Contents GV-DS1 Declaration of Conformity Dear CustomerPower Cord Protection Power SourcesPower Lines Grounding or PolarizationDamage Requiring Service AccessoriesCleaning Replacement PartsDo not place the Video Capture Docking Station Maintenance How to handle a CD-ROMVideo Capture Facility Jlip Video Capture SoftwareJlip Control Facility Data Sharing With Jlip Player Soft- wareHOW to Close the Program HOW the Desktop Works HOW to Open the ProgramPicture Format Setting IntroductionJlip Player Software Troubleshooting Major Specifications IndexGetting Started Video Printer Operation GV-PT2Create title indexes for your video collection Advanc ED AP P Licat IonsBusiness presentations Internet homepageCapture input EXT./printer connector Multi connector Jlip jack pPlay button Pause buttonImage sources with Jlip and video output connectors Video Capture Docking Station ConnectorCore filter EXTWhat is Jlip ? What is video capture software ?Operating Environment Connectable DevicesWindows Installation ProcedurePreparation HO W to Open the PRO GramSelect Transfer Rate. Normally select Initializing JlipSelect Units Itiali ZA TionHOW to Close the Program Control buttons Main Desktop WindowMenu bar Image display area Menu BARExit Each pulldown menu is configured as followsVCR operation window Capturing Video Images Image data flowRepeat steps 2 through 5 as required Step by Step CaptureFull image data is transferred to the computer Automatic Capture Ideo CA PtureProgram Capture Make sure all units are properly connected pTransfer Select Interval Capture Interval CaptureAutomatically Selecting a Picture Format Capture ModePicture Data Format Counter Value Change Counter ResetModify Capture Point window appears TransferredYou can change the Video Capture Unit’s ID number Delete Index Image and Full ImageChange ID Saving Create NEW FolderOpen the menu bar and click File New Album Saved, you will be asked whether to save or notSave the Full Image Data Open IndexOpen JLIPjlp File window is displayed Using Jlip Player Software DataSave As Jlip jlp File window is displayed HOW to Store Jlip Player DataProblem Cause Where the program run file Counter cannot be resetCannot capture video data With the desired counterMessage Appears when Action Execute after ErrorPlaying back Not enough diskMemo Jlip Player Software Section When connected with the Video Printer Connections When Using Jlip Playe r Soft wareJlip Digital camcorderDevices to connect to the Video Capture BOX Gettin G StartedInstalling Jlip Player Software Select Serial Port Starting Jlip Player SoftwarePrepare Devices Select Devices Title bar Drop Frame SystemElapsed Time MemoOperating camcorder Setting in/out pointsBasic Oper AT Ions Start Playback Select SceneTo confirm all programmed scenes, click Start Only the camcorder movesDubbing Basic OP Eration SPrepare NEW Tape Start EditingEnter File Name Start SavingSave File Select Floppy Disk DriveCorrecting and cutting the programmed counter data BA SIC OP E RationsOpening a saved file Designateied Scene to be COP Overwriting the fileStore Designated Scene in Memory Designate Scene to be TransferredIcon button Position button Power buttonStore button Scene selectPrint Bring UP Video Printer Window PrintingPlayback Store SceneAccess Picture Equalization Dialog BOX Adjusting picture equalizationQuitting the Movie Player window Click Close Choose Exit from FilePreparation Auto CaptureTo Print Captured Video Data with Video Printer Load the tape into the video unitClick Print to start printing To print only the cut-in scene on the edited tapeChanging ID number Connecting other device during operationAdvan CED Oper AT Ions Access Device Selection Dialog BOX Access Name Change Dialog BOXWhen Using the Video Capture Software Enter NEW Name SET NEW NameAdvanc ED Operat Ions Access Pause Time CORREC- Tion Dialog BOXEnter Value Determine ValueThat power is on Error - This application willPower on all devices System Communication error Check devices - ConfirmAjor Speci Ficat Ions Automatic Capture Auto Bitmap Setup MenuChange ID COM Port Delete Index Image and Full Image Desktop Window Pg , 48GV-DS1
Top Page Image Contents