JVC 0397MKVUNYP, LYT0002-0M1B, GV-DS1 Initializing Jlip, Select Transfer Rate. Normally select

Page 17

INITIALIZATION17

INITIALIZING JLIP

The first time you start the Video Capture software, JLIP initialization is required. This sets which of the computer’s COM ports (connector into which the RS-232C cable is plugged) is connected to the GV-CB1 JLIP Video Capture Docking Station. The initialization window automatically appears the first time you start the software after installation. Do not forget to carry out this JLIP initialization procedure. The JLIP must be initialized again whenever you connect a new image source or other unit to the JLIP Video Capture Docking Station.

1.

2.

3.

4.

Start the JLIP Video Capture software.

The "JLIP Initialization" screen automatically appears.

Select "COM Port".

•COM1 through COM4 ports are available. Check to see which COM port is connected to the JLIP Video Capture Box and select it.

Select "Transfer Rate". •Normally select 38400.

•38400 may not be available on some computers. When transmission errors take place during use, switch to 19200 or 9600. Image data transmission will be slower at these speeds.

5. Click "OK". The "JLIP Initialization" window appears while the program checks for the connected units.

JLIP Initialization
COM Port	COM 1

Transfer Rate

38400

OK

Cancel

NOTE : If you want to change a unit or COM port or Transfer Rate, select "Initialize" from "Set-up" in the menu bar to call up the "JLIP Initialization" window. Repeat this setting procedure.

If a connection is incorrect, a connected unit is not turned on, or the connection ID numbers overlap, the message "Connection error" appears. Click "OK" to return to the Main desktop.

Image 17

Contents GV-DS1 Declaration of Conformity Dear CustomerPower Cord Protection Power SourcesPower Lines Grounding or PolarizationDamage Requiring Service AccessoriesCleaning Replacement PartsDo not place the Video Capture Docking Station Maintenance How to handle a CD-ROMVideo Capture Facility Jlip Video Capture SoftwareJlip Control Facility Data Sharing With Jlip Player Soft- wareHOW to Close the Program HOW the Desktop Works HOW to Open the ProgramPicture Format Setting IntroductionJlip Player Software Troubleshooting Major Specifications IndexGetting Started Video Printer Operation GV-PT2Create title indexes for your video collection Advanc ED AP P Licat IonsBusiness presentations Internet homepageCapture input EXT./printer connector Multi connector Jlip jack pPlay button Pause buttonImage sources with Jlip and video output connectors Video Capture Docking Station ConnectorCore filter EXTWhat is Jlip ? What is video capture software ?Operating Environment Connectable DevicesWindows Installation ProcedurePreparation HO W to Open the PRO GramSelect Transfer Rate. Normally select Initializing JlipSelect Units Itiali ZA TionHOW to Close the Program Control buttons Main Desktop WindowMenu bar Image display area Menu BARExit Each pulldown menu is configured as followsVCR operation window Capturing Video Images Image data flowRepeat steps 2 through 5 as required Step by Step CaptureFull image data is transferred to the computer Automatic Capture Ideo CA PtureProgram Capture Make sure all units are properly connected pTransfer Select Interval Capture Interval CaptureAutomatically Selecting a Picture Format Capture ModePicture Data Format Counter Value Change Counter ResetModify Capture Point window appears TransferredYou can change the Video Capture Unit’s ID number Delete Index Image and Full ImageChange ID Saving Create NEW FolderOpen the menu bar and click File New Album Saved, you will be asked whether to save or notSave the Full Image Data Open IndexOpen JLIPjlp File window is displayed Using Jlip Player Software DataSave As Jlip jlp File window is displayed HOW to Store Jlip Player DataProblem Cause Where the program run file Counter cannot be resetCannot capture video data With the desired counterMessage Appears when Action Execute after ErrorPlaying back Not enough diskMemo Jlip Player Software Section When connected with the Video Printer Connections When Using Jlip Playe r Soft wareJlip Digital camcorderDevices to connect to the Video Capture BOX Gettin G StartedInstalling Jlip Player Software Select Serial Port Starting Jlip Player SoftwarePrepare Devices Select Devices Title bar Drop Frame SystemElapsed Time MemoOperating camcorder Setting in/out pointsBasic Oper AT Ions Start Playback Select SceneTo confirm all programmed scenes, click Start Only the camcorder movesDubbing Basic OP Eration SPrepare NEW Tape Start EditingEnter File Name Start SavingSave File Select Floppy Disk DriveCorrecting and cutting the programmed counter data BA SIC OP E RationsOpening a saved file Designateied Scene to be COP Overwriting the fileStore Designated Scene in Memory Designate Scene to be TransferredIcon button Position button Power buttonStore button Scene selectPrint Bring UP Video Printer Window PrintingPlayback Store SceneAccess Picture Equalization Dialog BOX Adjusting picture equalizationQuitting the Movie Player window Click Close Choose Exit from FilePreparation Auto CaptureTo Print Captured Video Data with Video Printer Load the tape into the video unitClick Print to start printing To print only the cut-in scene on the edited tapeChanging ID number Connecting other device during operationAdvan CED Oper AT Ions Access Device Selection Dialog BOX Access Name Change Dialog BOXWhen Using the Video Capture Software Enter NEW Name SET NEW NameAdvanc ED Operat Ions Access Pause Time CORREC- Tion Dialog BOXEnter Value Determine ValueThat power is on Error - This application willPower on all devices System Communication error Check devices - ConfirmAjor Speci Ficat Ions Automatic Capture Auto Bitmap Setup MenuChange ID COM Port Delete Index Image and Full Image Desktop Window Pg , 48GV-DS1