JVC GV-DS1, LYT0002-0M1B manual Basic OP Eration S, Dubbing, Prepare NEW Tape, Start Editing

Page 52

52

BASICOPERATIONS (cont.)

Dubbing

MOVIE PLAYER
File Edit Video Printer		Help
COUNTER Non Drop		00:01:30:10F		ID	06	FILE
POWER	ON OFF		MEMO
PROGRAM PLAYBACK			SCENE		STOP		MODE
SCENE	CUT IN		CUT OUT				STILL
01	00:01:30:12F		00:03:27:14F				PLAY
02	00:07:15:21F		00:10:40:18F				SEARCH
03	00:15:50:11F		00:20:33:10F				SLOW
							SLOW
							FF
ELAPSED TIME			00:10:04:28F				REW
ELAPSED TIME			00:10:04:28F
							IN/OUT
Rec On ! !

You can record all programmed scenes onto the tape in the recording deck.

Dubbing is possible only when the GR-DVM1 is connected.

1 PREPARE NEW TAPE

Make sure the erase protection tab on the tape is present. Then insert it into the recording deck and set the recording deck to the Record-Pause mode.

2 START EDITING

Click "START" on the MOVIE PLAYER window.

When editing stops, the camcorder enters the Stop mode and the recording deck enters the Record-Pause mode.

•During dubbing, do no operation other than pressing "STOP". If other opera- tions are done, a malfunction may occur.

3 STOP EDITING Stop the recording deck.

NOTES:

●Also refer to the camcorder's instruction manual on dubbing.

●There may be small margin between the CUT IN/OUT points you input and the dubbed scenes' ones.

●Dubbing is impossible if the JLIP connector of the camcorder also serves as an Edit jack.

Image 52

Contents GV-DS1 Dear Customer Declaration of ConformityPower Sources Power Cord ProtectionPower Lines Grounding or PolarizationAccessories Damage Requiring ServiceCleaning Replacement PartsDo not place the Video Capture Docking Station How to handle a CD-ROM MaintenanceJlip Video Capture Software Video Capture FacilityJlip Control Facility Data Sharing With Jlip Player Soft- wareHOW to Open the Program HOW to Close the Program HOW the Desktop WorksPicture Format Setting IntroductionTroubleshooting Major Specifications Index Jlip Player SoftwareGetting Started Video Printer Operation GV-PT2Advanc ED AP P Licat Ions Create title indexes for your video collectionBusiness presentations Internet homepageMulti connector Jlip jack p Capture input EXT./printer connectorPlay button Pause buttonImage sources with Jlip and video output connectors Connector Video Capture Docking StationCore filter EXTWhat is video capture software ? What is Jlip ?Operating Environment Connectable DevicesInstallation Procedure WindowsHO W to Open the PRO Gram PreparationInitializing Jlip Select Transfer Rate. Normally selectItiali ZA Tion Select UnitsHOW to Close the Program Menu bar Main Desktop WindowControl buttons Menu BAR Image display areaEach pulldown menu is configured as follows ExitVCR operation window Image data flow Capturing Video ImagesFull image data is transferred to the computer Step by Step CaptureRepeat steps 2 through 5 as required Ideo CA Pture Automatic CaptureProgram Capture Make sure all units are properly connected pTransfer Automatically Interval CaptureSelect Interval Capture Picture Data Format Capture ModeSelecting a Picture Format Counter Reset Counter Value ChangeModify Capture Point window appears TransferredChange ID Delete Index Image and Full ImageYou can change the Video Capture Unit’s ID number Create NEW Folder SavingOpen the menu bar and click File New Album Saved, you will be asked whether to save or notOpen Index Save the Full Image DataUsing Jlip Player Software Data Open JLIPjlp File window is displayedHOW to Store Jlip Player Data Save As Jlip jlp File window is displayedProblem Cause Counter cannot be reset Where the program run fileCannot capture video data With the desired counterMessage Appears when Action Error Execute afterPlaying back Not enough diskMemo Jlip Player Software Section Connections When Using Jlip Playe r Soft ware When connected with the Video PrinterDigital camcorder JlipGettin G Started Devices to connect to the Video Capture BOXInstalling Jlip Player Software Prepare Devices Starting Jlip Player SoftwareSelect Serial Port Select Devices Drop Frame System Title barMemo Elapsed TimeBasic Oper AT Ions Setting in/out pointsOperating camcorder Select Scene Start PlaybackTo confirm all programmed scenes, click Start Only the camcorder movesBasic OP Eration S DubbingPrepare NEW Tape Start EditingStart Saving Enter File NameSave File Select Floppy Disk DriveOpening a saved file BA SIC OP E RationsCorrecting and cutting the programmed counter data Overwriting the file Designateied Scene to be COPStore Designated Scene in Memory Designate Scene to be TransferredPosition button Power button Icon buttonStore button Scene selectPrint Printing Bring UP Video Printer WindowPlayback Store SceneAdjusting picture equalization Access Picture Equalization Dialog BOXQuitting the Movie Player window Click Close Choose Exit from FileAuto Capture PreparationTo Print Captured Video Data with Video Printer Load the tape into the video unitTo print only the cut-in scene on the edited tape Click Print to start printingAdvan CED Oper AT Ions Connecting other device during operationChanging ID number Access Name Change Dialog BOX Access Device Selection Dialog BOXWhen Using the Video Capture Software Enter NEW Name SET NEW NameAccess Pause Time CORREC- Tion Dialog BOX Advanc ED Operat IonsEnter Value Determine ValueError - This application will That power is onPower on all devices System Communication error Check devices - ConfirmAjor Speci Ficat Ions Setup Menu Automatic Capture Auto BitmapChange ID COM Port Delete Index Image and Full Image Desktop Window Pg , 48GV-DS1