Hitachi RAS-SX13HAK / RAC-SX13HAK, RAS-SX10HAK / RAC-SX10HAK

Page 20

DYNAMIC AIR DEFLECTION FUNCTION (TRACING/EVASION)

The infrared sensor can detect the position of people and automatically change the airflow direction.

1	Press the	AUTO AIR DEFLECTION button to switch the air deflection
	mode.			Example: Heating
				Example: Heating
	Pressing the DYNAMIC		Operation Description
	AIR DEFLECTION		Operation Description
	button
	button
			·(Tracing) Adjusts the airflow direction
			automatically to send the air flow to
			automatically to send the air flow to
			the location of the person.
			the location of the person.
			·(Tracing) Adjusts the airflow direction


			automatically to keep the air flow away
			from the location of the person.

		Release the	·Return to the setting prior to the dynamic
		Dynamic Air	air deflection mode.
		Dynamic Air
		Deflection button

·After the dynamic air deflection mode is set, the sensor usually works once every 15 seconds to 3 minutes to detect the position of the person and adjusts the airflow direction accordingly.

(The airflow direction does not change with the movement of human body immediately.)

·If the dynamic air deflection mode fails to achieve the desired effect, adjust the airflow direction manually.

·When the machine works in cooling, dehumidifying, or dry cool operation after the dynamic air deflection is set, if the indoor humidity/temperature is very high, the left/right/upper/lower air deflectors may change their angles to prevent drop of condensed water. After the temperature falls, the air conditioner returns to the dynamic air deflection status.

■How to change the detection speed of the sensor of the dynamic air deflection (tracing/evasion) function:

·There are 2 detection speeds: “Standard” (by intervals of 15"–3') and “Slow” (by intervals of 1'–10'). ·The remote controller is set to the standard speed by default.

·When the detection speed of the sensor is too high, set the detection speed to “Slow”

(when people and pets in the room behave frequently, resulting in frequent changes to the airflow direction).

Set the detection speed of the sensor to “Slow”.

1After the running stops, hold down for more than 5 seconds while pressing and holding. ·At this time, the air conditioner beeps for signal receiving.

·Return to the “Standard” mode by repeating the above procedure (until the air conditioner beeps for signal receiving).

In addition to “Standard” and “Slow” modes, you can also fine tune the detection speed of the sensor.

Fine tune the detection speed of the sensor

2 Hold down

after the running stops

3 Select the desire setting.

(Finely tuned within +3 to -3. The indicator turns off 10 seconds later)

4 Press the

(STOP) button

·The settings are saved.

– 20 –

Contents РУССКИЙ ∂ÏÏËÓÈÎ¿ PORTUGUÊS SPANISH ITALIANO FRANÇAIS DEUTSCH ENGLISH RAS-SX10HAK / RAC-SX10HAK RAS-SX13HAK / RAC-SX13HAKINDOOR UNIT OUTDOOR UNIT RAS-SX10HAK RAS-SX13HAKPRECAUTIONS DURING INSTALLATION PRECAUTIONS DURING SHIFTING OR MAINTENANCEPRECAUTIONS DURING OPERATION SAFETY PRECAUTIONENGLISH NAMES AND FUNCTIONS OF EACH PART INDOOR UNITOUTDOOR UNIT ABOUT OUTDOOR UNITINDOOR UNIT CONTROL PANEL / CLEANING UNIT How to Attach the Nano Titanium Air Cleaning Mesh PreparationREMOTE CONTROLLER NAMES AND FUNCTIONS OF EACH PART continuedBUTTONS TO START OPERATIONSFUNCTION SELECTOR POWERFULL Button1 Open the front panel INSTALLING ANTI-MOLD WASABI CASSETTE2 Install the anti-mold wasabi cassette Close the front panel FILTER CLEANING UNIT OPERATION CHECK 1 Make sure the power plug is firmly plugged into the power outlet2 Performing operation check after the power is turned on Perform the filter cleaning unit operation checkPREPARE THE REMOTE CONTROLLER Install the batteriesOpen the cover and press the RESET ABOUT ADDRESS SELECTOR SWITCHWHEN OPERATING THE REMOTE CONTROLLER PREPARE THE REMOTE CONTROLLER continuedAmpere setting Standard/Save can be selected Adjust the room temperature AUTOMATIC OPERATIONSTOP AUTOMATIC OPERATIONHEATING OPERATION DEHUMIDIFYING OPERATIONDEHUMIDIFYING OPERATION continued COOLING OPERATIONDRY COOL OPERATION 40 ％～70 ％ 10C~32C16C~32C Setting Range of AUTO/MANUAL OperationPOWERFUL OPERATION CANCELSTAINLESS PLASMA AIR PURIFYING FAN OPERATION STOPINFRARED HUMAN PRESENCE SENSING FUNCTION Example CoolingFine tune the detection speed of the sensor DYNAMIC AIR DEFLECTION FUNCTION TRACING/EVASIONSet the detection speed of the sensor to “Slow” INTERNAL CLEANING OPERATION STOP WhileSLEEP OPERATION MOLD MONITOR OPERATION ADJUSTING THE VERTICAL AIRFLOW DIRECTION Set automaticallyVertical airflow swing Vertical air flow of your preferenceHorizontal angle of your preference ADJUSTING THE HORIZONTAL AIRFLOW DIRECTIONAdjust the horizontal airflow direction How to preset the OFF TIMER ON TIMER TIMER PRESET OPERATIONHow to preset the timer РУССКИЙ ∂ÏÏËÓÈÎ¿ PORTUGUÊS SPANISH How to cancel the preset timerITALIANO FRANÇAIS DEUTSCH FURTHER CONVENIENT TIMER FUNCTION Combination of ON TIMER and DEHUMIDIFY buttonSLEEP TIMER OPERATION Combination of Sleep Timer and On Timer operationFILTER CLEANING OPERATION 1 Automatic filter cleaning operationConditions under which automatic filter cleaning is performed About the noise during filter cleaningITALIANO FRANÇAIS DEUTSCH ENGLISH STOP PressFILTER CLEANING OPERATION continued 2 Manual filter cleaning operation3 Maintenance HOW TO PROHIBIT THE FILTER CLEANING OPERATIONSet to prohibit the filter cleaning operation Return to the filter cleaning operation settingOperate the manual filter cleaning operation. Page Set to prohibit the filter cleaning operation againMAINTENANCE Maintenance of dust boxStop the operation with the remote controller and 3 Turn on the power supply or turn on the circuit breakerMaintenance of Stainless Mesh Filter controller and unplug the power plugStop the operation with the remote or turn off the circuit breakerMAINTENANCE continued Maintenance of mesh stainless filter continuedTurn on the power supply or turn on the circuit breaker Vacuum the dustMaintenance of dust catcher the power supply or turn off the circuit breakerStop the operation with the remote controller and unplug Remove the front panelMaintenance of electric dust collector electrodes 4 Turn on the power supply. or turn on the circuit breakerStop the operation with the remote controller and unplug the power supply or turn off theUNDERSTANDING THE OPERATING MECHANISM NAMES AND FUNCTIONS OF EACH PART PageTHE IDEAL WAYS OF OPERATION TROUBLESHOOTING FILTER CLEANING OPERATIONANTI-MOLD WASABI CASSETTE TROUBLESHOOTING continuedPLEASE CHECK THE FOLLOWING BEFORE SERVICE THE FOLLOWING CASES DOES NOT INDICATE MALFUNCTION Disconnect the power supply Reconnect the power supplyAutomatic operation starts when the temporary switch Unplug the powerINSPECTION AND MAINTENANCE REGULAR INSPECTIONOPERATION DISPLAY CHART During internal cleaning operation pageDuring preset of the mold monitor operation page DisplayMEMO 474 A РУССКИЙ ∂ÏÏËÓÈÎ¿ PORTUGUÊS SPANISH ITALIANO FRANÇAIS 中国语室内机室外机室内机／室外机分体式冷气机安全注意事项安装方面的注意事项搬移或修理时的注意事项使用上的注意事项使用上的注意事项各部的名称和功能室外机的说明纳米钛空清网的安装方法中国语室内机操作部和清扫部各部的名称和功能继续可以使运转开始的按钮功能选择部 2 安装防霉芥末盒。防霉芥末盒的安装1 打开前面板。 3 关上前面板。 2 进行接通电源后的动作检查。进行过滤网清扫部的动作检查。过滤网清扫部的动作确认1 将电源线可靠地接入电源中。警告请准备好遥控器装入电池。打开盖板用有尖细端头的物品按下复位操作遥控器时请准备好遥控器继续4 能够设定电流值标准/节省切换。自动运转自动运转室温的微调节风速的切换制热运转乾爽除湿运转可设定的温度范围为16C ~ 32C。围为 40% ~ 70% 。乾爽除湿运转继续制冷运转凉快运转干燥除湿、凉快运转的自动/手动切换 10 ～3250 ％～60 ％ 16 ～32乾爽除湿不锈等离子空气清净送风运转全功率运转红外线人体检知传感器以冷房运转为例动态导风（追踪/回避）运转机能以暖房运转为例传感器的检测速度设定为「慢速」传感器检测速度微调内部清洁运转快眠运转功能选择钮霉菌监视运转上下风向的调节自动设定上下风向摆动上下喜好风向左右喜好调节左右风向的调节左右风向的摆动 1 按 3 按定时器预约运转定时器的预约方法4 按定时预约的取消方法更方便的定时器使用方法开机定时与乾爽除湿钮的组合睡眠定时运转睡眠定时运转和开机定时的组合开机定时进行第二天早上的运转等。 1 预约开机定时。 74, 75页在过滤网清扫运转结束时 , 返回到过滤网清扫运转1 自动过滤网清扫运转进行自动过滤网清扫运转的条件过滤网清扫运转时的声音3 维护过滤网清扫运转（继续）2 手动过滤网清扫运转过滤网清扫运转禁止的设定方法清洁指示灯反复出现闪烁、亮灯和变暗现象。非故障 1 过滤网清扫运转禁止的设定方法。 2 重新设定过滤网清扫运转禁止的方法。 3 进行手动过滤网清扫运转 80页4 再一次设定过滤网清扫运转禁止的方法。 1 , 2 , 4 的设定方法, 80页集尘盒的保养方法请用遥控器停止操作，断开电源。或者切断断路器用水清洗集尘盒。接入电源。或打开断路器）在清扫机体前，请使用遥控器停止操作或者切断断路器。不锈过滤网的保养方法 1 请用遥控器停止操作，并断开电源。或者切断断路器 2 打开前面板。3 拆下前面板。 4 拆下前面的不锈过滤网。维护（继续）不锈过滤网的保养方法（继续）5 用吸尘器等吸掉灰尘。 6 安装不锈过滤网。捕尘器的保养方法请用遥控器停止操作，并断开电源。或者切断断路器。拆下捕尘器。维护继续电气集尘器电极的保养方法1 请用遥控器停止操作，并断下电源。或者切断断路器 2 请用双手轻轻打开上下导风板。注意 3 用牙刷清除电气集尘器电极的脏污。运转的原理和希望用户事前了解的事项各部的名称和功能 52页更理想的使用方法 1. 建议用户设定为“恰当的室温”, 既省钱又有益於身体。请不要将室温设定得过低或过高。对健康不利，且浪费电力。拉上窗帘或百叶遮帘, 可以减少热量的进出, 更有效地用电。 2. 请时常换气。注意如果与燃气器具同一室使用时，必要进行换气。 3. 要外出时, 可有效利用霉菌监视功能。（请参照霉菌监视运转） 4. 就寝时, 可有效利用定时功能。遇到问题时过滤网清扫部的动作的说明请服务人员维修以前，请先检查以下事项遇到问题时继续防霉芥茉盒的说明这非有故障运转指出现下述情况时,请迅即向销售店咨询暂时运转进行暂时运转时，请先断开电源。或切断断路器。）再次接入电源。或打开断路器。）按下暂时运转开关后, 会进行自动运转。定期检查检查整备运转显示快查表内部清洁运转中Page 474 A