Cobra Electronics MRHH325VP owner manual USA/International/Canada Channel Maps, VibrAlert Mode

Page 25

Operating Your Radio

Set Channel Map

Active Channel Map Icon

Channel Up/Down Button

42 English

Setup Mode Programming

USA/International/Canada Channel Maps

Three (3) sets of VHF Channel Maps have been established for marine use in the USA, Canada, and the re st of the world (International). Most of the channels are the same for all three (3) maps, but there are definite differences (see table on pages 20 through 27). Your radio has all three (3) maps built into it and will operate correctly in whichever area you choose.

To Set Channel Map Operating Area:

1.The Channel Map mode is the first mode that begins the Marine (VHF) Setup programming.

2.U, I and C will display, with the current setting (the U icon is the default) flashing.

3.Press Channel Up/Down button to select the U, I or C icon.

4.Press Call/Enter/Setup button to save this entry and move to the next setup programming mode.

NOTE

One or two of the channel maps might have been disabled for sales of this radio in some countries.

Operating Your Radio

VibrAlert® Tone Alert

Setup Mode Programming

VibrAlert® Mode

In VibrAlert® mode, your radio can alert you to incoming signals by sounding an audible call tone, a silent vibration or both.

To set VibrAlert®:

1.The display will show either the Vibrate icon (shake bars), Call Tone icon (bell shape) or a combination VibrAlert® icon.

2.The present setting of either, 01, 02 or 03 will be flashing.

3.Press Channel Up/Down button to select one of the following:

01 = VibrAlert® On (both shake bars and bell shape).

02 = Vibrate On (shake bars only).

03 = Call Tone Only On (bell shape only).

4.Press Call/Enter/Setup button to save this entry and move to the next setup programming mode.

Nothing Comes Close to a Cobra® 43

Image 25

Contents Customer Assistance For Assistance in the U.S.A Our Thanks to You Customer AssistanceFor Assistance Outside the U.S.A Backlit LCD Screen Product Features Radio Controls IndicatorsProduct Features Backlit LCD Liquid Crystal Display ScreenEmergency Weather Alert Signal Strength MeterSpeaker/Mic Jack Unlimited Memory Channels Roger Beep Tone SelectableTable of Contents Safety Training Information Important Safety InformationImportant Safety Information Recommendations for Marine Communication Recommendations for Marine CommunicationFCC Licensing Information VHF Marine Radio Procedures Voice Calling Voice CallingVoice Calling Vessel Corsair is calling the vessel VagabondEmergency Messages and Distress Procedure Emergency Messages Distress ProcedureRadiotelephone Calls Radiotelephone CallsMarine Distress Procedure Marine Emergency SignalsIf You Hear a Distress Call Emergency Messages and Distress Procedure VHF Marine Channel Assignments VHF Marine Channel Assignments International Distress, Safety and Calling03A Government Only 21A U.S. Government Only Canada Coast Guard Only 20A Port Operations Port Operations, Ship Movement23A Government Only Digital Selective Calling Voice communications not allowed 64A U.S. Government Only Canada Commercial Fishing81A U.S. Government Only Environmental Protection Operations Noaa Emergency Weather Alert Noaa Weather Channels AlertNoaa Test Alert System Weather Frequency/ChannelAntenna, Wrist Strap Included in this PackageBelt Clip Initial Charge Batteries and ChargerBatteries and Charger Alkaline Batteries Maintaining the Battery ChargeGetting Started Power/Volume/Squelch Controls Power On/Off ControlCommon Radio Functions Getting StartedScan Button Backlight/Key Lock ButtonSetup Mode Programming Setup Mode ProgrammingHigh/Medium/Low H-M-L Power Button To Toggle Between H-M-L Power ModesUSA/International/Canada Channel Maps VibrAlert ModeTo Set Channel Map Operating Area To set VibrAlertRoger Beep Mode Call Tone ModeKey Tone Mode Standby/Receive TransmitStandby/Receive and Transmit Marine Standby and Receive Rx ModeTo Set WX Alert On or Off To Set WX Auto Search Scan On or OffWeather WX Standby Mode Transmit Tx ModeWX Alert Standby Mode To Transmit a MessageAdvanced Operation Channel 16/9 ModeAdvanced Operation Tri-Watch Setup To Program or Edit the Tri-Watch Channels Tri-Watch ModeUsing Tri-Watch Tri-Watch Scan Mode Advanced OperationTo Exit Memory Location Mode Memory Location ModeTo Program Memory Locations To Recall a Stored Memory LocationChannel Scan Mode Product FeaturesMemory Location Scan Mode To Enter Channel ScanMaintenance Maintenance TroubleshootingTroubleshooting Specifications Limited 3-Year Warranty Warranty and Trademark Specifications AcknowledgementFor Products Purchased In The U.S.A For Products Purchased Outside The U.S.AAccessories Product ServiceAccessories