Cobra Electronics MRHH325VP owner manual Advanced Operation, Tri-Watch Mode

Page 30

Operating Your Radio

TRI-WATCH Button

TRI and MEM Icons

Channel Up/Down Button

52 English

Advanced Operation

Tri-Watch Mode

Tri-Watchmode gives you one (1) button access to scan a total of three (3) channels of most importance to you. Channel 16 is preprogrammed and will always be one (1) of the scanned locations. Two (2) other channels of your choice can be stored in the radio. These channels can be edited and/or recalled during future engagements of Tri-Watchmode.

NOTE

The radio must be squelched for Tri-Watchmode to function. See page 37 for Squelch procedure.

Tri-Watch Setup

To Program or Edit the Tri-Watch Channels:

1.Press and hold the TRI-WATCHbutton for two (2) seconds to activate Tri-Watch Setup mode. The TRI and MEM icons on the display will turn On.

NOTE

The main channel number will flash to indicate channel position. If there is no input activity for 15 seconds, the radio will sound two (2) beeps and return to Marine Standby mode.

2.Press Channel Up/Down button to select the desired Tri-Watchchannel.

3.Press and release TRI-WATCHbutton or Call/Enter/Setup button to confirm entry.

4.Repeat steps 2 and 3 to program the remaining additional Tri-Watchmemory channel.

5.After programming both Tri-Watchmemory channels the radio will immediately engage Tri-Watchmode. (See page 53 for further details.)

Operating Your Radio

TRI-WATCH Button

Tri-Watch Scan Mode

Advanced Operation

Using Tri-Watch

Tri-Watch Scan Mode:

1.From Marine Standby mode, press the TRI-WATCHbutton. The TRI icon will appear on the LCD display and the radio will scan through the three (3) Tri- Watch memory channels.

2.A signal on any one (1) of the three (3) channels will stop the scan for 10 seconds to allow you to listen to the traffic on that location.

NOTE

After the Tri-Watchscan stops to monitor a channel, as long as you do not press any buttons within 10 seconds, your radio will automatically resume scanning the Tri-Watchchannels.

3.Press the Channel Up/Down button to resume scanning the Tri-Watchchannels or to change the scan direction.

4.To EXIT the Tri-Watchscan, press the TRI-WATCHbutton again. The TRI icon will disappear from the LCD and the radio will return to Marine Standby mode.

Nothing Comes Close to a Cobra® 53

Image 30
Contents Our Thanks to You Customer Assistance Customer Assistance For Assistance in the U.S.AFor Assistance Outside the U.S.A Product Features Radio Controls IndicatorsBacklit LCD Screen Product Features Backlit LCD Liquid Crystal Display ScreenSpeaker/Mic Jack Signal Strength MeterEmergency Weather Alert Unlimited Memory Channels Roger Beep Tone SelectableTable of Contents Important Safety Information Safety Training InformationImportant Safety Information Recommendations for Marine Communication Recommendations for Marine CommunicationFCC Licensing Information VHF Marine Radio Procedures Voice Calling Voice CallingVoice Calling Vessel Corsair is calling the vessel VagabondRadiotelephone Calls Emergency Messages Distress ProcedureEmergency Messages and Distress Procedure Radiotelephone CallsMarine Emergency Signals Marine Distress ProcedureIf You Hear a Distress Call Emergency Messages and Distress Procedure VHF Marine Channel Assignments International Distress, Safety and Calling VHF Marine Channel Assignments03A Government Only 20A Port Operations Port Operations, Ship Movement 21A U.S. Government Only Canada Coast Guard Only23A Government Only 64A U.S. Government Only Canada Commercial Fishing Digital Selective Calling Voice communications not allowed81A U.S. Government Only Environmental Protection Operations Noaa Test Alert System Noaa Weather Channels AlertNoaa Emergency Weather Alert Weather Frequency/ChannelIncluded in this Package Antenna, Wrist StrapBelt Clip Batteries and Charger Initial ChargeBatteries and Charger Maintaining the Battery Charge Alkaline BatteriesCommon Radio Functions Power/Volume/Squelch Controls Power On/Off ControlGetting Started Getting StartedBacklight/Key Lock Button Scan ButtonHigh/Medium/Low H-M-L Power Button Setup Mode ProgrammingSetup Mode Programming To Toggle Between H-M-L Power ModesTo Set Channel Map Operating Area VibrAlert ModeUSA/International/Canada Channel Maps To set VibrAlertKey Tone Mode Call Tone ModeRoger Beep Mode Standby/Receive TransmitTo Set WX Alert On or Off Marine Standby and Receive Rx ModeStandby/Receive and Transmit To Set WX Auto Search Scan On or OffWX Alert Standby Mode Transmit Tx ModeWeather WX Standby Mode To Transmit a MessageChannel 16/9 Mode Advanced OperationAdvanced Operation Using Tri-Watch Tri-Watch Scan Mode Tri-Watch ModeTri-Watch Setup To Program or Edit the Tri-Watch Channels Advanced OperationTo Program Memory Locations Memory Location ModeTo Exit Memory Location Mode To Recall a Stored Memory LocationMemory Location Scan Mode Product FeaturesChannel Scan Mode To Enter Channel ScanMaintenance Troubleshooting MaintenanceTroubleshooting For Products Purchased In The U.S.A Warranty and Trademark Specifications AcknowledgementSpecifications Limited 3-Year Warranty For Products Purchased Outside The U.S.AProduct Service AccessoriesAccessories