Stop mode, Checkpoint for Still Timer setting | Panasonic AJ-D250P

Operation

STOP mode

1

When the STOP button is pressed, the STOP mode is established.

The STOP lamp lights, and the tape stops traveling.

OIn order to protect the tape, the tape protection mode will be established when the time selected for the “STILL TIMER” setup menu item setting has elapsed. (See page 31) When the STOP, REW, FF or PLAY button is pressed, the corresponding mode will be established.

<Checkpoint for STILL TIMER setting>

ORepeatedly using the same locations on the same tape will increase the cumulative standby time at those locations. In the interest of protecting the tape, keep the standby times at the same locations as short as possible.

ON	EJECT

OFF

POWER		MENU
POWER	LOCAL	REMOTE
DIGITAL VIDEO CASSETTE	Digital Video Cassette Recorder

INPUT SELECT

	S-VIDEO
LINE	OPTION AUDIO
	REC LEVEL
BEGIN END		CH 1
AUDIO OUT		CH 2
	SELECT
CH 3

CH 4

RESET COUNTER

REW	STOP			FF		PLAY		PAUSE/STILL			REC
MODE	DOWN					-				+	SET
			MENU		UP			DATA

REMOTE

1

12

Image 12

Panasonic AJ-D250P operating instructions Stop mode, Checkpoint for Still Timer setting

Contents

S0699W3119 a VQT8188-2 FCC Note Contents Features Introduction Parts and Their Functions Front panelCounter display Power switch LOCAL/MENU/REMOTE switch? Input Select switch Cassette insertion slot Headphones jack Volume controlRemote connector Reset button Connector panel Signal GND terminal Video in connectorREF Video in connector Audio in connectors Tapes Tape DescriptionCassette Checkpoints for consumer-use DV tape playback Turning on the power/inserting a cassette Turn on the unit’s power Insert the cassette tapeOperation Check that the Stop lamp is lighted Stop mode Checkpoint for Still Timer setting Recording Press the Play button while holding down the REC buttonPress the Stop button to end the recording Pause/record frame-to-frame continuity PlaybackCue/review Still picture playback Audio switching Frame by frame advance Setting the Begin and END points Menu mode Select TC or CTL using the Counter button. NoteRepeat playback Setting the Begin and END points Front panel Setting the repeat playback modeDisplaying the Begin and END points Time Codes and User’s Bit Time codesUser’s bit TCR 00 07 04 Setting the time code Setting the user’s bitNow follow the same procedure as for setting the time code Down button Stop button Playing back the time code/user’s bit 00 07 04 Superimposed Screens Display positionCharacters displayed Superimpose Screens Setup Initial Settings How to perform the settings using the on-screen menusHow to restore the factory settings How to set the user default settings How to load the user default settings How to initiate the menu protect mode How to release the menu protect mode How to display the Diag menu Setup Menus Setting Description of setting Superimposed DisplayUnderlining denotes the factory mode setting System menu Basic menu Operation menu Interface menu Tape Protect menu Time Code menu Video menu Audio menu Editing PreparationOperation Audio editing functions CuttingFading Noise may appear here at the joins in the edit points First Edit Function Preparing the editing tape First edit for assemble editingFirst edit for insert editing Interface specifications RS-232CCommunication parameters External interface specifications Sending format computer VTR$ Data format 3AH Receiving format VTR computer Example Command list $ List of commandsOAudio control commands OCounter control commands ODisplay control commands OEdit control commandsOMedia operation control commands OInput/output control commands OOperation control commands OQuery control commands OCommunication control commands OSearches control commands OTimer control commands $ Audio control commands $ Counter control commandsParameters Sets the signal to be regenerated when the TCG time code $ Display control commands CTL data referenceTC data reference $ Edit control commands OWhen the CTL data is to beMenu item Setting Setting command Used as the reference $ Media operation control commands $ Input/output control commandsM1 HEX display M2 HEX display $ Operation control commands STX OBF ETXSTX ORC ETX Case of a Dvcpro format tape Case of a DV format tapeSTX OSF ETX Parameters OIn the case of a Dvcpro Format tape STX OSR ETX $ Query control commands CTL modeTC mode, UB mode, Remain mode OIn the case of CTL data Ff = Frames Auto Back OFF STX QHC ETX Rewind Play Play Pause STX QHR ETXRewind Eject Switching data Parameter M1 HEX display M2 HEX display Bits supportedOWith no parameter OSP Stop AD AD AD AD ADAD9ADAADBADCADDADEADF Addressf OBitmap table a Cassette RF Video Tape Hard ACK OFF STX QRS ETX Repeat ONE Time Continue OFF STX QSY ETX OBitmap table B OWhen CTL data is to be used as ReferenceVideo Option STX QVM ETX $ Communication control commands OParameter setting normalOParameter setting no completion command $ Search control commands OWhen CTL data is to be used OWhen the counter value is to OWhen the parameter value forOWhen the parameter value for Which the TC data serves as Be stored in the memory OWhen the designated position is not to be entered Searches the counter value at the time when the command Data = wghmmssff Still mode is established upon completion $ Timer control commands $ Mode transition table Play REC Pause Audio Insert Pause $ Send commands and data returned from $ Send command intervalsCheckpoints for RS-232C communication Error Messages Error No Description Procedure for removing the tape manually in an emergency Emergency Eject Video Head Cleaning MaintenanceCondensation Specifications $ Input connectors$ Output connectors $ Digital video $ Digital audio Page Executive Office Mid-Atlantic/New EnglandSoutheast Region Central Region